Share information:
Manual gearbox car Toyota 4Runner 2 (N120)
Cars with a 4-cylinder engine are equipped with a W59 manual transmission, cars with V6 engines are equipped with R150 or R150F boxes. Repair of a gearbox with a complete disassembly is advisable to carry out in a car service.
Technical data of manual transmission
Tightening torques (Nm) Clutch housing mounting bolts 16 Reinforcement plate bolts 33 Cross member bolts 52 Transmission Mount Bolts 16 Transmission to engine mounting bolts 66
Tightening torques (Nm) Clutch housing mounting bolts 16 Reinforcement plate bolts 33 Cross member bolts 52 Transmission Mount Bolts 16 Transmission to engine mounting bolts 66
Rear gearbox oil seal (on rear-wheel drive vehicles)
Replacement 1. A common cause of leaks in the gearbox housing is wear of the rear seal in the housing tailpiece and bushing (if provided), as well as the oil seal and the sealing ring of the speedometer gearbox. These...
Replacement 1. A common cause of leaks in the gearbox housing is wear of the rear seal in the housing tailpiece and bushing (if provided), as well as the oil seal and the sealing ring of the speedometer gearbox. These...
Gearbox housing supports — inspection and replacement
1. Insert the pry bar between the crossbar and the support pad and rock it. 2. The crankcase should not be displaced much from the support. If wear of the support is detected, (rubber peeling), replace the support. 3....
1. Insert the pry bar between the crossbar and the support pad and rock it. 2. The crankcase should not be displaced much from the support. If wear of the support is detected, (rubber peeling), replace the support. 3....
Gearbox control lever — removal and installation
1. Remove the center section of the front panel (see subsection 10.24 ). 2. Unscrew the lever handle (photo on the left). Remove 4 screws (shown by arrows in the photo on the right), remove the cover and flange. 3. On...
1. Remove the center section of the front panel (see subsection 10.24 ). 2. Unscrew the lever handle (photo on the left). Remove 4 screws (shown by arrows in the photo on the right), remove the cover and flange. 3. On...
Removal and installation of manual transmission
Removal 1. Disconnect the battery from ground. 2. Remove the lever. 3. On rear wheel drive vehicles, remove the N₂ engine shield. On 4WD vehicles, remove both shields. 4. Disconnect the propeller shaft. 5. Remove the...
Removal 1. Disconnect the battery from ground. 2. Remove the lever. 3. On rear wheel drive vehicles, remove the N₂ engine shield. On 4WD vehicles, remove both shields. 4. Disconnect the propeller shaft. 5. Remove the...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other Toyota models
➥ Mechanical gearbox Toyota RAV 4 XA10 (1994-2000)
➥ Manual gearbox Toyota Corolla E80 (1983-1990)
➥ Mechanical gearbox Toyota Corona T190 (1992-1997)
➥ Mechanical gearbox Toyota Camry XV30 (2001-2006)
➥ Mechanical gearbox Toyota Cruiser 70 (1985-1996, diesel)
➥ Manual gearbox Toyota Dyna Y50/Y60 (1984-1995)
Link in different formats to this article
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- 4-cylinder engines
- 6-cylinder engines
- Engine overhaul
- Cooling and heating
- Fuel system
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Clutch
- Transmission line
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Ignition system
- Power devices
- Electrical circuits