Car manual transmission Toyota Carina 6 (T190)

Manual transmission — general information
The gearbox type is stamped on an aluminum plate attached to the engine compartment bulkhead in the line "TRANS / AXLE". For gearbox oil change, see chapter " Maintenance and general check and adjustment procedures ".

The device of the drive shaft seals
1, 3 - drive shaft, 2 - retaining ring, 4, 5 - retaining ring, 6, 11 - drive shaft, 7 - steering rod end, 8, 9 - cotter pin, 10 - lock nut cap, 12 - oil seal, 13 - O-ring seal, 14 - washer, 15 - bolt, 16, 19 - lower...

Replacing drive shaft seals
1. Remove the front wheels. 2. Remove the parts according to the drawing " Replacing drive shaft seals ". 3. Remove the seals. a) Remove the left drive shaft oil seal. b) Remove the right drive shaft oil seal as shown...

Gear shift lever device
1 - gear shift cable, 2 - gear selection cable, 3 - guide, 4 - holder, 5 - guide, 6 - cable retainer, 7 - lower trim of the central console, 8 - parking brake hole trim, 9 - gear shift lever handle, 10 - lid, 11 - gear...

Gearbox assembly
Note: remove and install as shown in the figure "Removing and installing the gearbox assembly". Removal and installation of the gearbox assembly 1 - drive shaft, 2 - retaining ring, 3 - transition coupling, 4 - stopper,...

Gearbox device (C50)
1 - release bearing, 2 - clutch release fork, 3 - case, 4 - speed sensor, 5 - gear shift lever housing support bracket, 6 - clutch housing, 7 - oil receiver, 8 - adjusting washer, 9 - outer bearing ring, 10 -...

Primary shaft device (C50)
1 - primary shaft, 2 - third gear pinion, 3 - synchronizer clutch No.2, 4 - cracker, 5 - spring, 6 - synchronizer ring, 7, 14 - needle bearing, 8 - fourth gear pinion, 9 - retaining ring, 10 - rear ball bearing, 11 -...

Secondary shaft device (C50)
1 - pin, 2 - ball, 3 - secondary shaft, 4 - spacer sleeve, 5, 13 - needle bearing, 6, 9 - synchronizer ring, 7 - synchronizer clutch No.1, 8 - synchronizer hub No.1, 10 - retaining ring, 11 - spring, 12 - cracker, 14 -...

Gear Selector Shaft Design (C50)
1 - retaining ring, 2 - spring seat, 3 - inner shift lever No.2, 4 - internal selection lever, 5 - spring, 6 - spring seat, 7 - oil seal, 8 - anther, 9 - gear selection lever rod, 10 - gear selector shaft cover, 11 -...

Gearbox device (S50)
1 - primary shaft bearing holder, 2 - speed sensor, 3 - gear selector lever shaft assembly, 4 - pin and plug, 5 - reverse gear engagement limiter, 6 - blocking device No.1, 7 - reversing light switch, 8 - crank lever, 9...

Primary shaft device (S50)
1 - primary shaft, 2, 9 - synchronizer ring, 3 - spacer, 4 - needle bearing, 5 - fourth gear pinion, 6 - rear bearing, 7, 14 - retaining ring, 8 - pin, 10 - cracker, 11 - third gear pinion, 12 - needle bearing, 13 -...

Secondary shaft device (S50)
1 - pin, 2 - secondary shaft, 3 - thrust washer, 4 - first gear pinion, 5 - needle bearing, 6 - synchronizer ring, 7 - synchronizer sleeve No.1, 8 - synchronizer spring, 9 - synchronizer clutch No.1, 10 - cracker, 11 -...

Gear Selector Shaft Device (S50)
1, 10 - retaining ring, 2 - reverse gear limiter holder, 3 - inner shift lever No.2, 4, 8 - spring, 5 - inner shift lever No.1, 6 - pin, 7 - inner shift lever housing, 9 - shift fuse bracket, 11 - gear selection lever...

Differential device (S50)
1 - driven gear of the main transmission, 2 - oil seal, 3 - adjusting washer, 4 - outer bearing ring, 5 - bearing, 6 - thrust washer, 7 - satellite, 8 - satellite axis, 9 - axle gear, 10 - thrust washer, 11 - oil seal,...

4WD Models Transmission — General Information
4WD vehicles have permanent all-wheel drive, the so-called "Full Itime 4WD", with interaxle differential lock. Note: For more detailed information on the operation of the systems, please refer to the chapter "Operating...

Transfer case device
Note: For the procedure for changing the oil in the transfer case, see chapter " Maintenance ". 1 - transfer case oil pipe, 2 - adjusting gasket, 3 - O-ring seal, 4 - oil seal, 5 - anther, 6 - driven gear bearing...

The device of the main gear drive pinion of the transfer case
With mechanical interaxle differential locking system 1, 2 - bearing, 3 - shaft of the main transmission drive gear, 4 - main gear drive pinion. With viscous coupling 1 - bearing, 2 - right cup of the main gear drive...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Car gearbox Toyota Cruiser 60/80 (1980-1997, petrol)
➥ Manual gearbox Toyota Corolla E80 (1983-1990)
➥ Mechanical gearbox Toyota Corona T190 (1992-1997)
➥ Mechanical gearbox Toyota Camry XV30 (2001-2006)
➥ Manual gearbox Toyota RAV 4 XA20 (2000-2005)
➥ Mechanical gearbox Toyota 4Runner N120 (1989-1995)

Link in different formats to this article

TEXTHTMLBB Code