Suspension and steering technical data Moment of resistance to turning the ball joint pin: - bottom 0.08 - 2.17 Nm – top 0.6 - 3.0 Nm Tightening torques (N·m) Front suspension Lower ball joint bolts 72 Lower ball joint nuts 129 Upper ball joint nuts 98 Nuts...
Springs and dampers (racks) front suspension Details of the front suspension strut 1, 4. Plate; 2, 5. Pillow; 3. Upper suspension cup; 6. Spring; 7. Shock absorber; 8. Sleeve Attention! Keep in mind that the procedure for removing the springs is extremely...
Front suspension stabilizer — removal and installation 1. Raise the front of the car. 2. Loosen the nuts (indicated by arrows) stabilizer rods. 3. Turn away bolts (nuts) (indicated by arrows) bushing clamps. 4. Remove the stabilizer. 5. Remove the stabilizer bushings. 6....
Swivel fist — removal and installation 1. Raise the front of the car and remove the wheels. 2. Remove the speed sensor (arrow indicates bolt). 3. Remove the brake caliper. 4. Remove the brake disc. 5. Remove the brake shield (on the left - brake shield bolts...
Front hub and bearing Replacement 1. Remove the steering knuckle. 2. Car front hub and bearing "Toyota 4 Runner/ Hilux/ Surf" pressed into a fist, removed and changed in a car service. 3. Assembly is carried out in the reverse order.
Ball joints — check and replacement Hub, steering knuckle and upper support of the car "Toyota 4-Runner/ Hilux/ Surf" 1. Case; 2. Collar; 3. Retaining ring; 4. Top support; 5. Fist; 6. Bearing; 7. Hub; 8. Oil seal; 9. Retaining ring; 10. Brake shield; 11....
Upper arm — removal and installation Upper arm 1. Cotter pin; 2. Sleeve; 3. Lever Attention! The procedure applies to rear- and all-wheel drive vehicles. Removal and installation 1. Raise the front of the car. 2. Remove the caliper and set aside. 3....
Lower arm — removal and installation Lower suspension arm car "Toyota 4-Runner/ Hilux/ Surf" 1. Rear eccentric; 2. Buffer 2; 3. Lever; 4. Buffer 1; 5. Front eccentric Removal and installation 1. Raise the front of the car and remove the wheels. 2. Remove...
Rear shock absorbers — removal and installation Details of fastening of the rear shock absorber 1. Washers; 2. Pillows; 3. Shock absorber; 4. Bushings Removal and installation 1. Raise the rear of the vehicle by placing jack stands under the axle beam and remove the...
Rear anti-roll bar — removal and installation 1. Raise the rear of the car. 2. Loosen the nuts (indicated by arrows) and remove the stabilizer links. 3. Turn away bolts (indicated by arrows) bushing clamps. 4. Remove the stabilizer. 5. Check up a condition of...
Rear axle cross bar — removal and installation 1. Raise the rear of the car. 2. Place pedestals under the bridge beam. 3. Disconnect the brake pressure regulator from the axle. 4. Detach the bar from the frame bracket (the arrow indicates the fastening nut). 5....
Rear springs — removal and installation 1. Raise the rear of the car. 2. Place pedestals under the bridge beam. 3. Pass the chain through the coils of the spring and secure with a bolt to prevent accidental loss of the spring when the axle is lowered. The...
Longitudinal rods of the rear axle — removal and installation 1. Raise the rear of the car. 2. Place pedestals under the bridge beam. 3. Disconnect the speed sensor wiring from the booms. 4. To remove the upper rod, unscrew the nuts (indicated by arrows), remove the washers and...