Share information:
Vehicle owner's manual Toyota 4Runner 2 (N120)
Introduction to the Operation and Repair Manual
For cars "Toyota 4Runner/Hilux/Surf" 4-cylinder injection engines are installed (in-line cylinder) or 6-cylinder (with V-shaped cylinder arrangement) engines with cylinder volumes of 2.7 and 3.4 liters, respectively....
For cars "Toyota 4Runner/Hilux/Surf" 4-cylinder injection engines are installed (in-line cylinder) or 6-cylinder (with V-shaped cylinder arrangement) engines with cylinder volumes of 2.7 and 3.4 liters, respectively....
Instrument panel
1. Combined instruments; 2. Headlight and direction indicator switch; 3. Release lever for adjusting the steering wheel height; 4. Side nozzle; 5. Headlight washer switch or headlight controller-switch; 6. Rear fog...
1. Combined instruments; 2. Headlight and direction indicator switch; 3. Release lever for adjusting the steering wheel height; 4. Side nozzle; 5. Headlight washer switch or headlight controller-switch; 6. Rear fog...
Combination instruments
Combination instruments (in a car without a tachometer) 1. Daily mileage counter; 2. Speedometer; 3. Warning and indicator lights; 4. Fuel gauge; 5. Direction indicator lights 6. Odometer; 7. Engine temperature gauge;...
Combination instruments (in a car without a tachometer) 1. Daily mileage counter; 2. Speedometer; 3. Warning and indicator lights; 4. Fuel gauge; 5. Direction indicator lights 6. Odometer; 7. Engine temperature gauge;...
Designation of the symbols of the light indicators of the instrument cluster
Brake Malfunction Indicator Light Low battery indicator light Oil pressure warning light Engine System Failure Warning Light Anti-lock braking system malfunction indicator light Door Not Closed Warning Light Additional...
Brake Malfunction Indicator Light Low battery indicator light Oil pressure warning light Engine System Failure Warning Light Anti-lock braking system malfunction indicator light Door Not Closed Warning Light Additional...
Car keys
Cars equipped with a system of increased security of access to the trunk The master key fits every lock. The spare key does not fit the trunk lock. To protect items locked in the trunk, leave a spare key with an...
Cars equipped with a system of increased security of access to the trunk The master key fits every lock. The spare key does not fit the trunk lock. To protect items locked in the trunk, leave a spare key with an...
Immobilizer system (engine start code recognition)
The immobilizer is an anti-theft system. When the ignition key is inserted into the lock, the radio beacon chip generates a coded signal that is received by the car's anti-theft system. The engine will start only if the...
The immobilizer is an anti-theft system. When the ignition key is inserted into the lock, the radio beacon chip generates a coded signal that is received by the car's anti-theft system. The engine will start only if the...
Unlocking and locking doors
Locking the door with a key To lock the door, turn the key towards the front of the car; to unlock, turn the key towards the rear of the car. On vehicles equipped with electric door locks, all interior doors and the...
Locking the door with a key To lock the door, turn the key towards the front of the car; to unlock, turn the key towards the rear of the car. On vehicles equipped with electric door locks, all interior doors and the...
Electrical equipment of doors
Each door is equipped with an electric window lifter. Raising and lowering the windows is possible when the ignition key is turned to the On position. Driver's side glass drive To operate the glass on the driver's side,...
Each door is equipped with an electric window lifter. Raising and lowering the windows is possible when the ignition key is turned to the On position. Driver's side glass drive To operate the glass on the driver's side,...
Front seat adjustment
Front seat 1. Handle for adjusting the side supports (driver's seat) 2. Lumbar support control lever (driver's seat) 3. Seat lock release lever 4. Seat cushion angle adjuster (at the driver's) 5. Lever for setting the...
Front seat 1. Handle for adjusting the side supports (driver's seat) 2. Lumbar support control lever (driver's seat) 3. Seat lock release lever 4. Seat cushion angle adjuster (at the driver's) 5. Lever for setting the...
Steering wheel tilt adjustment
To adjust the tilt of the steering wheel, pull the locking lever, set the steering wheel to the desired position and release the lever. Warning! It is prohibited to adjust the steering wheel position while driving....
To adjust the tilt of the steering wheel, pull the locking lever, set the steering wheel to the desired position and release the lever. Warning! It is prohibited to adjust the steering wheel position while driving....
Adjusting the position of the rearview mirror
The rear view mirror position is adjusted using a handle. Warning! If the mirror is jammed due to icing, do not operate the handle. Apply de-icer to restore mirror movement. Adjusting the position of the rear-view...
The rear view mirror position is adjusted using a handle. Warning! If the mirror is jammed due to icing, do not operate the handle. Apply de-icer to restore mirror movement. Adjusting the position of the rear-view...
Interior lighting fixture
To turn on the interior lighting, move the switch lever. In the DOOR position of the switch lever, the light turns on when any of the doors is opened (side and back). Individual lighting plafond To turn on, press the...
To turn on the interior lighting, move the switch lever. In the DOOR position of the switch lever, the light turns on when any of the doors is opened (side and back). Individual lighting plafond To turn on, press the...
Windscreen wiper and washer
To turn on the wiper, move the lever to the desired position. To turn on the washer, press the button on the end of the lever. The ignition key must be in the On position. To enable single operation of the cleaner (when...
To turn on the wiper, move the lever to the desired position. To turn on the washer, press the button on the end of the lever. The ignition key must be in the On position. To enable single operation of the cleaner (when...
Rear window wiper and washer
To turn on the wiper and washer, turn the handle on the end of the lever to the desired position. The ignition key must be in the On position. When the lever is in the INT position, the windshield wiper will operate in...
To turn on the wiper and washer, turn the handle on the end of the lever to the desired position. The ignition key must be in the On position. When the lever is in the INT position, the windshield wiper will operate in...
Headlights and direction indicators
To turn on the headlights, turn the handle at the end of the lever. On some vehicles, the following lights come on when the engine is started (the headlight switch is in the Off position). First click position: Only the...
To turn on the headlights, turn the handle at the end of the lever. On some vehicles, the following lights come on when the engine is started (the headlight switch is in the Off position). First click position: Only the...
Headlight washer
To wash the headlights, turn on the headlights and press the button The ignition key must be in the On position. Check the fluid level in the tank through the transparent wall from time to time. Top up with windshield...
To wash the headlights, turn on the headlights and press the button The ignition key must be in the On position. Check the fluid level in the tank through the transparent wall from time to time. Top up with windshield...
Rear window defroster
To defrost the rear window to remove moisture or ice, press the button. The ignition key must be in the On position. Under the influence of heat generated by thin wires of the heating element mounted on the inner...
To defrost the rear window to remove moisture or ice, press the button. The ignition key must be in the On position. Under the influence of heat generated by thin wires of the heating element mounted on the inner...
Oil pressure gauge, voltmeter, tachometer and odometer
Oil pressure gauge Voltmeter Tachometer Total mileage counter and daily mileage counter
Oil pressure gauge Voltmeter Tachometer Total mileage counter and daily mileage counter
Signs and warning signals
If the car is released from the handbrake, then stop and check Stop and check Stop and check Contact your dealer's service center. Fuel reserve indicator light is on. Fill the tank Contact the dealer's auto service...
If the car is released from the handbrake, then stop and check Stop and check Stop and check Contact your dealer's service center. Fuel reserve indicator light is on. Fill the tank Contact the dealer's auto service...
Checking service reminder signs
1. Put the car on the handbrake. 2. Open one of the side doors or the back door. 3. Close the door. The indicator light should go out. 4. Turn the ignition key to the ACC position. The airbag indicator light should come...
1. Put the car on the handbrake. 2. Open one of the side doors or the back door. 3. Close the door. The indicator light should go out. 4. Turn the ignition key to the ACC position. The airbag indicator light should come...
Ignition switch and steering column lock
Cars with gasoline engines Start – turns on the starter. After releasing, the key returns to the On position. On – switching on the engine electrical equipment and all consumers. Corresponds to the driving conditions....
Cars with gasoline engines Start – turns on the starter. After releasing, the key returns to the On position. On – switching on the engine electrical equipment and all consumers. Corresponds to the driving conditions....
AM-VHF radio receiver with electronic tuning
Using the radio 1. Turn on the receiver by turning the "PWR.VOL" knob clockwise. 2. Adjust the volume further by turning the "PWR.VOL" knob. 3. Tune to the desired station (see below, items 1–10 and items 1–6). 4. To...
Using the radio 1. Turn on the receiver by turning the "PWR.VOL" knob clockwise. 2. Adjust the volume further by turning the "PWR.VOL" knob. 3. Tune to the desired station (see below, items 1–10 and items 1–6). 4. To...
AM-VHF radio with electronic tuning
Using the receiver 1. Turn on the receiver by pressing the LMU button, select stereo or mono reception mode, or press the TI button to receive a traffic information station (see below). The display will show L, M, or U....
Using the receiver 1. Turn on the receiver by pressing the LMU button, select stereo or mono reception mode, or press the TI button to receive a traffic information station (see below). The display will show L, M, or U....
Adjusting the air flow direction
System controls 1. Air conditioner on/off button; 2. Turn off; 3. Turn on; 4. Air flow direction regulator; 5. Air intake adjustment lever; 6. Air recirculation; 7. Outside air; 8. In the face; 9. Flow to the legs and...
System controls 1. Air conditioner on/off button; 2. Turn off; 3. Turn on; 4. Air flow direction regulator; 5. Air intake adjustment lever; 6. Air recirculation; 7. Outside air; 8. In the face; 9. Flow to the legs and...
Heater controls
Heater controls and their purpose The temperature regulator sets the air temperature at the entrance to the passenger compartment and also turns the heater on and off. In the extreme left position of the handle, the...
Heater controls and their purpose The temperature regulator sets the air temperature at the entrance to the passenger compartment and also turns the heater on and off. In the extreme left position of the handle, the...
Clock — setting the time
The digital clock shows the time when the ignition key is in the ACC or On position. To reset the hours, press the H button. To reset the minutes, press the M button. To set the time in hours, press the:00 button. For...
The digital clock shows the time when the ignition key is in the ACC or On position. To reset the hours, press the H button. To reset the minutes, press the M button. To set the time in hours, press the:00 button. For...
Cigarette lighter, ashtray and glove box
To turn on, press the cigarette lighter button. When it is hot enough, the button automatically "unclicks". When the engine is not running, the ignition key must be in the ACC position. Do not hold the cigarette lighter...
To turn on, press the cigarette lighter button. When it is hot enough, the button automatically "unclicks". When the engine is not running, the ignition key must be in the ACC position. Do not hold the cigarette lighter...
Actions in case of engine failure to start
The simplest checks Before checking, make sure that the vehicle has sufficient fuel. If the vehicle is equipped with an engine start coding system (immobilizer), then start the engine with other keys from the set. If...
The simplest checks Before checking, make sure that the vehicle has sufficient fuel. If the vehicle is equipped with an engine start coding system (immobilizer), then start the engine with other keys from the set. If...
Starting the engine in case of cylinder overflow with gasoline
In the event of a failure to start, the engine cylinders may become overfilled with gasoline due to repeated unsuccessful starting attempts. On engines 4E-FE, 4A-FE, 7A-FE Turn the ignition key to the START position and...
In the event of a failure to start, the engine cylinders may become overfilled with gasoline due to repeated unsuccessful starting attempts. On engines 4E-FE, 4A-FE, 7A-FE Turn the ignition key to the START position and...
Removal air from the fuel system
If the fuel is used up, then after refueling the vehicle, the engine may fail to start. In this case, pump fuel until you feel resistance.
If the fuel is used up, then after refueling the vehicle, the engine may fail to start. In this case, pump fuel until you feel resistance.
Starting the engine in emergency conditions
If the fuel is used up, then after refueling the vehicle, the engine may fail to start. In this case, pump fuel until you feel resistance. Caution: Make sure that the starting battery has a rated voltage of 12 V.
If the fuel is used up, then after refueling the vehicle, the engine may fail to start. In this case, pump fuel until you feel resistance. Caution: Make sure that the starting battery has a rated voltage of 12 V.
Starting from an additional battery
1. If the engine is to be started from another car's battery, the car bodies must not touch. Disconnect all extraneous consumers (lighting devices and additional electrical equipment). 2. If necessary, remove the plugs...
1. If the engine is to be started from another car's battery, the car bodies must not touch. Disconnect all extraneous consumers (lighting devices and additional electrical equipment). 2. If necessary, remove the plugs...
If the engine stalls while driving
Attention! When the engine is not running, due to the inactivity of the vacuum booster and hydraulic booster, you will have to apply slightly more force to the brake pedal and steering wheel. 1. Reduce speed gradually...
Attention! When the engine is not running, due to the inactivity of the vacuum booster and hydraulic booster, you will have to apply slightly more force to the brake pedal and steering wheel. 1. Reduce speed gradually...
Actions in case of a puncture of a tire
Reduce speed gradually without changing direction. Pull over to the side of the road and stop on a level, hard-surfaced area. Stop the engine and turn on the hazard warning lights. Move the lever to position P (on...
Reduce speed gradually without changing direction. Pull over to the side of the road and stop on a level, hard-surfaced area. Stop the engine and turn on the hazard warning lights. Move the lever to position P (on...
Vehicle identification numbers
When compiling operating manuals and spare parts catalogs, numerical vehicle codes are used, so when selecting and installing the necessary parts, it is necessary to know the identification code (identification) car...
When compiling operating manuals and spare parts catalogs, numerical vehicle codes are used, so when selecting and installing the necessary parts, it is necessary to know the identification code (identification) car...
Lifting a car with a jack
Before lifting the vehicle, engage reverse gear or move the automatic transmission selector to Park. When changing a wheel or performing other work, install the jack under the following areas of the body. Raising the...
Before lifting the vehicle, engage reverse gear or move the automatic transmission selector to Park. When changing a wheel or performing other work, install the jack under the following areas of the body. Raising the...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other Toyota models
➥ User manual Toyota RAV 4 XA10 (1994-2000)
➥ User manual Toyota Camry Vista V40 (1994-1998)
➥ User manual Toyota Corona T190 (1992-1997)
➥ User manual Toyota Carina T190 (1992-1996)
➥ User manual Toyota Duet (1998-2004)
➥ User manual Toyota Corolla Verso 3 (2004-2009)
Link in different formats to this article
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- 4-cylinder engines
- 6-cylinder engines
- Engine overhaul
- Cooling and heating
- Fuel system
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Clutch
- Transmission line
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Ignition system
- Power devices
- Electrical circuits