Car front and rear suspension Toyota Carina 6 (T190)

Preliminary checks
1. Check tire wear and tire pressure when cold. 2. Check the wheel runout. Runout - less than 3.0 mm 3. Check the axial clearance of the hub bearings. 4. Check the reliability of the suspension parts fastening. 5. Check...

Checking the front wheel alignment
1. To stabilize the suspension, rock the car up and down. 2. Set the wheels in the direction of travel straight ahead and roll the car forward about five meters. 3. Place the measuring part of the device in the center...

Checking the front wheel steering angles
1. Place the vehicle on swivel wheels. Attention: - The check is performed with the brake pedal pressed. - Remove the brake light fuse. 2. Check the wheel turning angles.

Checking the camber, longitudinal and transverse tilt of the front wheel steering axes
1. Remove the decorative cap. 2. Remove the cotter pin and cap. Note: To perform the inspection, wheels with alloy wheels must be replaced with wheels with regular wheels. 3. Install the special tool on the hub as shown...

Front wheel alignment
Note: After adjusting the camber, check the amount of toe-in of the front wheels. 1. Remove the front wheels. 2. Loosen the two nuts on the bottom of the strut. 3. Adjust the camber by moving the lower part of the...

Checking and adjusting rear wheel alignment
1. To stabilize the suspension, rock the car up and down. 2. Set the wheels in the direction of travel straight ahead and roll the car forward about five meters. 3. Place the measuring part of the device in the center...

Checking the rear wheel alignment
1. Remove the decorative cap. 2. Install the special tool on the hub as shown in the figure. 3. Install a device for measuring the camber and lateral tilt of the steering axes. 4. Check the camber of the front wheels,...

Front suspension strut device
1 - rack assembly, 2 - plug, 3 - upper support of the rack, 4 - seal, 5 - upper spring seat, 6 - upper vibration isolator, 7 - spring, 8 - front suspension strut, 9 - compression stroke limiter, 10 - lower vibration...

Front Suspension Strut — Removal
1. Jack up the car, remove the front wheel, 2. Unscrew the brake hose mounting bolt. 3. Unscrew the bolts securing the speed sensor wire and the sensor itself. 4. Disconnect the strut from the steering knuckle by...

Front Suspension Strut — Installation
1. Install the lower vibration absorber on the stand. 2. Install the spring compression stroke limiter onto the piston rod. 3. Install the spring. a) Using the special tool, compress the spring. b) Install the spring on...

Front Lower Suspension Arm — Removal
1. Jack up the car, remove the front wheel. Tightening torque - 105 Nm 2. (2WD) Remove the exhaust pipe. Tightening torque - 44 Nm 3. Remove the lower engine protection cover. 4. Disconnect the stabilizer struts from...

The device of the lower arm of the front suspension
1 - anti-roll bar, 2 - steering gear assembly, 3 - cross beam, 4 - bushing, 5 - additional brace of the cross beam, 6 - lower arm of the front suspension, 7 - exhaust pipe, 8 - gasket, 9 - lower engine protection...

Lower Ball Joint — Removal
1. Remove the steering knuckle assembly £ with the hub (see the relevant section). 2. Remove the ball joint. a) Using a screwdriver, remove the dust cover. b) Remove the cotter pin and nut. c) Using a puller, remove the...

Checking the lower ball joint
Check the ball joint rotation moment. a) Before installing the nut, rock the ball joint axle from side to side 5 times. b) Using a torque wrench, rotate the nut continuously (one revolution in 2-4 seconds) and take a...

Lower ball joint device
1 - front drive shaft, 2 - anther, 3, 7, 11 - cotter pin, 4 - steering rod end, 5 - rotation speed sensor, 6 - steering knuckle assembly with hub, 8 - brake disc, 9 - lock nut cap, 10 - lock nut, 12 - lower ball joint,...

Lower Ball Joint — Installation
1. Install the ball joint. a) Install the ball joint and tighten the nut. Tightening torque - 105 Nm b) Install a new cotter pin. Note: when installing the cotter pin, the nut can be turned at an angle of no more than...

Transverse stability stabilizer device
2WD 1 - stabilizer mounting bracket, 2 - bushing, 3 - stabilizer bar, 4 - stabilizer strut, 5 - additional brace of the cross beam, 6 - rear engine support, 7 - steering gear assembly, 8 - cross beam, 9 - front engine...

Anti-roll bar — removal
1. Jack up the car, remove the front wheel. Tightening torque - 105 Nm 2. Remove the lower engine protection cover. 3. (2WD) Remove the exhaust pipe. Tightening torque - 44 Nm 4. Disconnect the stabilizer struts from...

Checking the anti-roll bar
Check the rotation moment of the stabilizer bar ball joint. a) Before installing the nut, rock the ball joint axle from side to side 5 times. b) Using a torque wrench, rotate the nut continuously (one revolution in 2-4...

Anti-roll bar — installation
1. Installation is carried out in the reverse order of removal. 2. When installing, refer to the assembly drawing. 3. When installing the bushings on the stabilizer, do it as shown in the figure. 4. After installation,...

Removal the steering knuckle with the front axle hub
1. Jack up the car, remove the front wheel. 2. Unscrew the bolts securing the speed sensor wire and the sensor. 3. Unscrew the brake hose mounting bolt. 4. Unscrew the two bolts and remove the caliper assembly. Hang the...

Front axle hub device
1 - front drive shaft, 2, 5, 15 - cotter pin, 3 - steering rod end, 4 - rotation speed sensor, 6 - brake disc, 7 - lock nut cap, 8 - lock nut, 9 - hub bolt, 10 - anther, 11, 19 - oil seal, 12 - retaining ring, 13, 18 -...

Disassembling the front axle hub
1. Using a screwdriver, remove the dust cover. 2. Remove the lower ball joint from the steering knuckle a) Remove the cotter pin and unscrew the nut. b) Using a puller, remove the lower ball joint from the steering...

Front axle hub assembly
1. Install the bearing. a) Remove the inner ring from the bearing. b) Using a special tool and a press, install the new bearing into the steering knuckle. c) Install the inner bearing ring. 2. Using a drift and hammer,...

Installing the steering knuckle with the front axle hub
1. Install the hub assembly with the steering knuckle. a) Connect the lower suspension arm to the ball joint. Note: Be careful not to damage the hub oil seal, dust cover and rotor of the speed sensor (ABS). b) Install...

Replacing the front axle hub bolt
1. Jack up the car, remove the front wheel. 2. Remove the caliper assembly and brake disc. Attention: - do not disconnect the brake hose - apply marks on the disk and hub - Avoid getting oil on the disc. 3. Using a...

Rear suspension strut device
1 - plug, 2 - rear suspension strut assembly, 3 - bushing, 4 - upper support of the rack, 5 - compression stroke limiter, 6 - spring, 7 - lower vibration isolator, 8 - rear suspension strut.

Rear suspension strut — removal
1. Remove the rear seat cushion and backrest, 2. Remove the seat belt. 3. Remove the rear pillar side trim. 4. Remove the decorative brake light cover and additional brake light. 5. Remove the rear shelf. 6. Remove the...

Rear suspension strut — installation
1. Install the lower vibration isolator on the rack, aligning the recesses. 2. Install the spring compression stop and bushing on the piston rod as shown in the figure. 3. Install the spring. a) Using the special tool,...

The design of the lower and longitudinal suspension arms
2WD 1 - rear beam, 2 - washer, 3 - lower suspension arm No.2, 4 - lower suspension arm No.1, 5 - nut, 6 - gasket, 7 - central muffler pipe, 8, 10 - lower suspension arm tips No.2, 9 - lever adjustment tube. 4WD 1 - rear...

Lower and trailing arms (2WD) — removal
1. Jack up the car and remove the rear wheel. 2. Remove the center muffler pipe. 3. Disconnect the parking brake cable. 4. Unscrew the two bolts and nuts and remove the trailing arm. 6. Remove lower suspension arm No.2....

Disassembling the lower control arm #2
1. Loosen the two lock nuts. 2. Rotate the adjusting tube to disassemble the lower suspension arm No.2. 3. Unscrew the lock nuts from the levers.

Assembly of the lower control arm No. 2
1. Install the locknuts on the levers. 2. Rotate the adjusting tube to assemble the lower suspension arm No.2. 3. Adjust the length of lower suspension arm No.2 by turning the adjusting tube. Lever length - 493.3±1.5 mm...

Lower and trailing arms (2WD) — installation
1. Install lower control arm #1. a) Raise the rear beam with a jack. b) Install lower suspension arm #1 with washer and bolt. Note: Orient the lever with the paint mark towards the rear. c) Install the second lever...

Lower and trailing arms (4WD) — removal
1. Jack up the car and remove the rear wheel. 2. Remove the center muffler pipe. 3. Disconnect the propeller shaft from the rear axle gearbox. a) Apply marks to the cardan shaft and gearbox shaft. b) Unscrew the four...

Lower and trailing arms (4WD) — installation
1. Install lower control arm #1. a) Connect lower control arm No.1 to the rear beam. Note: Orient the lever with the painted mark towards the rear. b) Jack up the rear beam, install the rear beam bushing and secure it...

Rear wheel hub device (2WD)
1 - speed sensor (ABS), 2 - brake mechanism support, 3 - brake drum, 4 - brake disc, 5 - rear wheel hub assembly, 6 - O-ring seal, 7 - hub bolt, 8 - hub bearing, 9 - hub shaft.

Rear suspension stabilizer bar device
1 - stabilizer strut, 2 - anti-roll bar, 3 - stabilizer bracket, 4 - bushing.

Rear suspension anti-roll bar — removal and installation
Removal 1. Jack up the car and remove the rear wheels. Tightening torque - 105 Nm 2. Remove the stabilizer struts. Note: If the ball joint axle rotates with the nut, use a socket wrench to hold the strut in place....

Checking the rear stabilizer bar
Check the rotation moment of the stabilizer bar ball joint. a) Before installing the nut, rock the ball joint axle from side to side 5 times. b) Using a torque wrench, rotate the nut continuously (one revolution in 2-4...

Rear Wheel Hub (2WD) — Removal and Installation
Removal 1. Jack up the car, remove the rear wheel. Tightening torque - 105 Nm 2. (Disc brakes) Disconnect the brake hose, remove the caliper and disc. Tightening torque of mounting bolts: Calipers - 48 Nm Brake hose -...

Disassembling the rear wheel hub
Caution: If the model is with ABS, do not disassemble the rear wheel hub and bearing. 1. Loosen the lock nut. a) Using a hammer and chisel, loosen the nut. b) Unscrew the lock nut. 2. Remove the bearing. a) Using a...

Replacing the rear wheel hub bolt
(See the relevant subsection of the section " Front suspension ").

Assembling the rear wheel hub
Install the bearing. a) Using a special tool and a press, install the new bearing onto the hub. b) Install and tighten the new lock nut. Tightening torque - 123 Nm c) Lock the nut.

Rear Wheel Knuckle (2WD) — Removal and Installation
Removal 1. Jack up the car and remove the rear wheel. Tightening torque - 105 Nm 2. (Drum brakes) Remove the brake drum. 3. (Disc brakes) Remove the caliper and brake disc. Tightening torque - 48 Nm 4. Remove the speed...

Rear wheel knuckle device (2WD)
1 - speed sensor (ABS), 2 - fist, 3 - washer, 4 - brake mechanism support, 5 - rear wheel hub, 6 - O-ring seal, 7 - nut, 8 - brake mechanism, 9 - brake drum.

Rear wheel hub and knuckle assembly (4WD)
1, 6 - oil seal, 2 - fist, 3 - inner bearing ring, 4 - bearing, 5 - retaining ring, 7 - anther, 8 - hub. Note: Apply consistent grease to the parts indicated by the arrows.

Rear Wheel Hub and Knuckle (4WD) — Removal and Installation
Removal 1. Remove the rear wheel. Tightening torque - 105 Nm 2. Loosen the lock nut. a) Remove the cotter pin and lock nut cap. b) Loosen the lock nut by pressing the brake pedal. Tightening torque - 220 Nm 3. Remove...

Rear Wheel Hub and Knuckle (4WD) — Disassembly
1. Using a puller, remove the hub from the knuckle. 2. Using a special tool and a press, remove the inner bearing ring from the hub. 3. Unscrew the four nuts securing the brake shield. 4. Remove the seals from the...

Rear Wheel Hub and Knuckle (4WD) — Assembly
1. Install the bearing into the knuckle. Note: If the bearing was disassembled, install the inner rings in the same places as before disassembly. a) Remove the inner rings from the new bearing. b) Using a suitable...

Replacing the hub bolt
1. Jack up the car, remove the rear wheel. 2. Remove the caliper assembly and brake disc. Attention: - do not disconnect the brake hose - apply marks on the disk and hub - Avoid getting oil on the disc. 3. Using a...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Car suspension Toyota Corolla Verso 3 (2004-2009)
➥ Car suspension Toyota Dyna Y50/Y60 (1984-1995)
➥ Car suspension Toyota 4Runner N120 (1989-1995)
➥ Car suspension Toyota Camry XV10 (1991-1996)
➥ Car suspension Toyota RAV 4 XA10 (1994-2000)
➥ Car suspension Toyota Highlander 1 (2000-2007, petrol)

Link in different formats to this article

TEXTHTMLBB Code