Front and rear suspension of the car Toyota Highlander 1 (XU20)

Suspension and steering specifications
Tightening torques for threaded connections Nm, unless otherwise specified Front suspension Ball joint Ball joint to steering knuckle mounting nut - 123 Nuts and bolts for fastening the ball joint to the wishbone - 127...

General information about the suspension
The front suspension uses a traditional MacPherson strut design. The upper end of each strut is connected to a strut support on the car body. The lower end of the strut is attached to the upper end of the steering...

Front Anti-Roll Bar Bushings and Struts — Removal and Installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Note: Removing the stabilizer bar requires removing the steering gear and...

Front suspension strut assembly — removal, inspection and installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Removal 1. Loosen the wheel nuts, lift the car and place reliable...

Front Suspension Wishbone — Removal, Inspection and Installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Removal 1. Loosen the wheel nuts on the appropriate side, lift the front...

Strut assembly with spring — replacement
Note: The following procedure applies to struts that are not used on vehicles with electronic air suspension. 1. If the struts or springs show signs of wear (leaks, loss of damping characteristics, coating chipping,...

Ball joints — replacement
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. 1. Loosen the wheel nuts, lift the car and place reliable supports under...

Steering knuckle and hub — removal and installation
Warning! Dust generated during normal operation of the brake system is harmful to health. Never blow it out with compressed air or inhale it. Always use a certified filter mask when working on the brakes. Under no...

Front hub assembly with bearing — removal and installation
Because pressing the hub and bearing out of the steering knuckle requires special tools and experience, this job should be left to professionals. However, the steering knuckle and hub can be removed as a single unit and...

Rear Anti-Roll Bar and Bushings — Removal and Installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. 1. Loosen the rear wheel mounting nuts. Raise the rear of the car and...

Rear suspension strut assembly — removal, inspection and installation
Removal Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Application: When removing/replacing any rear suspension...

Rear Suspension Trailing Arm — Removal and Installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Application: When removing/replacing any rear suspension components,...

Rear suspension wishbones — removal and installation
Caution: If the vehicle is equipped with electronically controlled air suspension, turn off the height control switch before raising the vehicle. Application: Please note that the painted markings on all rear suspension...

Rear hub assembly with bearing — removal and installation
Warning! Dust generated during normal operation of the brake system is harmful to health. Never blow it out with compressed air or inhale it. Always use a certified filter mask when working on the brakes. Under no...

Rear hub support — removal and installation
Warning! Dust generated during normal operation of the brake system is harmful to your health. Never blow it out with compressed air or inhale it. Always use a certified filter mask when working on the brakes. Under no...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Car suspension Toyota Corolla Verso 3 (2004-2009)
➥ Car suspension Toyota Duet (1998-2004)
➥ Car suspension Toyota Cruiser 70 (1985-1996, diesel)
➥ Car suspension Toyota Carina T190 (1992-1996)
➥ Car suspension Toyota 4Runner N120 (1989-1995)
➥ Car suspension Toyota Camry XV10 (1991-1996)

Link in different formats to this article

TEXTHTMLBB Code