Car front and rear suspension Toyota Duet

Disassembling drive shafts (2WD models with manual transmission and 4WD)
1. Remove the inner joint dust boot clamps. Note: Do not damage the boot. 2. Lower the dust cover and remove the grease from the joint. 3. Remove the retaining ring using a screwdriver. 4. Remove the outer race of the...

Preliminary check
1. Check the tire size and the amount of wear on the wheels and tires. a) Check the discs for cracks, breaks, dents, etc. b) Inspect the tires for excessive wear and deformation. Also make sure there are no foreign...

Checking and adjusting the front wheel alignment angles
Note: Check and adjust wheel alignment angles on a flat, horizontal surface. Checking the convergence Note: The vehicle must be unloaded when performing the check. 1. Rock the car up and down to stabilize the...

Front shock absorber
Removal 1. Jack up the car. 2. Remove the front wheel. 3. Disconnect the brake hose clamp. 4. (Models with ABS) Disconnect the wheel speed sensor wire. 5. Remove the spring. a) Loosen the center nut on the shock...

Lower control arm of the front suspension
Removal 1. Jack up the car. 2. Remove the front wheels. 3. Disconnect the anti-roll bar link. Lower arm of the front suspension. 1 - steering knuckle, 2 - lower arm of the front suspension. 4. Using the special tool,...

Front suspension anti-roll bar
Removal and installation Anti-roll bar. 1 - bushing bracket, 2 - bushing, 3 - anti-roll bar, 4 - rubber bushing, 5 - lower suspension arm. Note: Installation is carried out in the reverse order of removal. 1. Jack up...

Front axle hub
Check on the car 1. Jack up the car. 2. Remove the front wheel. 3. Disconnect the brake hose clamp. 4. Hang the brake caliper on the wire. Note: Do not damage the brake hose. 5. Remove the brake disc. Note: Do not drop...

Rear shock absorber
Removal 1. Jack up the car. 2. Remove the rear wheel. 3. (2WD) Jack up the rear suspension beam on both sides. Note: Use a block of wood as a spacer between the beam and the jack. 4. (4WD) Jack up the rear axle. 5....

Rear suspension beam (2WD models)
Removal and installation Note: Installation is carried out in the reverse order of removal. Perform final tightening of the bolts after the suspension has been stabilized. 1. Jack up the car. 2. Remove the rear wheels....

Rear Axle (4WD Models)
Removal and installation Note: Installation is carried out in the reverse order of removal. Tightening torques are given in the text. Perform final tightening of the bolts after the suspension has been stabilized. 1....

Rear axle shaft
Removal 1. Jack up the car. 2. Remove the wheel. 3. Drain the oil from the rear gearbox. 4. (Models with ABS) Remove the rear wheel speed sensor. 5. Disconnect the brake pipe and brake hose. 6. Remove the brake drum. 7....

Rear axle hub
Check on the car 1. Check the hub runout. Maximum runout - 0.8 mm 2. Measure the bearing axial clearance. Maximum gap - 0.2 mm Removal 1. Jack up the car. 2. Remove the wheel. 3. Remove the brake drum. 4. Using a...

Main technical data of the suspension
Specifications Tightening torques for threaded connections

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Car suspension Toyota Corolla Verso 3 (2004-2009)
➥ Car suspension Toyota Carina T190 (1992-1996)
➥ Car suspension Toyota 4Runner N120 (1989-1995)
➥ Car suspension Toyota RAV 4 XA10 (1994-2000)
➥ Suspension and axle shafts Toyota Camry XV20 (1996-2001)
➥ Car suspension Toyota Highlander 1 (2000-2007, petrol)

Link in different formats to this article

TEXTHTMLBB Code