Instrumentation and controls 1. Indicator of the state of the brake system. A) The indicator lights up if the parking brake is on; the level of brake fluid is low or the tightness of the vacuum brake booster is broken; the indicator circuit is...
Multifunction display The multifunction display shows the following information: Times of Day; indications of the navigation system; ambient air temperature; warning about exceeding the set speed; setting the alarm time; information...
Clock — setting the time Time setting is carried out by pressing the control buttons located on the display panel: Click on the button ":00", thus setting the minutes. If you need to set from 0 to 29 minutes, you must press the V button (M),...
Navigation system The navigation system allows you to determine the direction of the car. Compass accuracy depends on your location (underground garages, tunnels, in the city, etc.). When the compass fails, the following image lights up...
Ambient temperature The car is equipped with a system that allows you to determine the ambient temperature. To do this, use the button to select "MODE" this mode. Note: The ambient air temperature sensor is located in the area of the front...
Buzzer exceeding the set speed This function allows you to monitor the excess of the set speed. In case of exceeding, the computer informs with three sound signals. To set the speed limit, press the switch "MODE". This should display the following...
Alarm clock — time setting The operation of the alarm clock does not depend on the position of the ignition switch and works even when the ignition is completely turned off. The alarm time is set with the buttons "H" And "M". Pushing the button...
Diagnostic mode When the engine is running, malfunctions are displayed on the monitor, and a buzzer sounds at the same time. If the ignition key is in the position "ACC". and the door is not tightly closed, the corresponding...
Light signaling on the car 1. Switch for headlights and direction indicators. Note: The headlight and turn signal switch operates independently of the ignition switch. A) When the knob is turned to the first click, the dimensions, license plate...
Door lock 1. The set usually includes several keys: main and additional. The master key allows you to start the engine, open the doors, trunk and glove box. An additional key allows you to open the driver's door, start the...
Power window — control The windows can be adjusted in two ways: from the control panel on the driver's door or from the control panel on the passenger's door. There is a switch on the panel of each door, by pressing which the passenger can...
Hood lock lever To open the hood, release the trunk lock by pulling up on the latch as shown in the illustration. Then open the hood from the outside using the lock lever. To open the hood, you need to pull the lever up, as shown in...
Trunk lock lever To unlock the trunk lid, pull up on the lever located on the right side of the driver's seat. When the trunk is opened, the backlight automatically turns on. From the outside, the trunk is opened by turning the key to...
Filler neck hatch To open the filler flap, pull up on the lever located on the left under the driver's seat.
Wiper switch Interval adjustable switch To turn on and stop the cleaner, it is necessary to move the switch to one of the positions: 1st position - full suspension; 2nd position - intermittent mode (after 3-12 sec); 3rd position -...
Washer switch Switch without interval adjustment When you press the button located on the lever, the front glass washer is turned on and after 1 second the wiper is turned on for 2-3 strokes. Interval adjustable switch To turn on the...
Mirror cleaning switch The system allows you to clean the mirrors from water using vibration and heated mirrors. For the system to work, you must turn on the ignition, press the switch. The operation of the system is accompanied by the...
Wiper de-icer switch The windshield wiper de-icer heats the top surface of the windshield and removes ice from the blades and windows. The defroster is activated by pressing the switch located as shown in the figure. In this case, the...
Steering wheel adjustment The steering wheel is adjusted mechanically. To adjust the position of the steering wheel, pull the lock lever towards you, set the steering wheel to the desired position.
Mirror management Mirrors are adjusted from the control panel on the instrument panel. In this case, the ignition key must be in position "ON" or "ACC". Before driving, it is necessary to fold the mirrors to a characteristic click....
Seat adjustment 1. Adjusting the longitudinal position of the front seats. To adjust the longitudinal position of the front seats, move the lever up and move the seat to the desired position. After adjustment, return the adjustment...
Heating and air conditioning control Description To turn on the air conditioner, you must operate one of the switches "A/C" or "ECON". When turned on, the indicators light up. In mode "ECON" the air conditioner is in economy mode. The heater works when the...
Idle speed control On some models (cold climate option, diesel or manual transmission models) an idle speed control system is installed. The system increases the idle speed and efficiency of the heating system when the knob is turned to...
Radio — highlights of operation Radio The quality of radio signal reception can vary significantly while the car is moving due to the terrain, weather conditions and the proximity of sources of electromagnetic radiation. Cassette player About once a...
Radio — general information The radio is turned on by turning knob 8, and the same knob controls the sound volume. By pressing button 11"AM-FM" selected range (AM or FM). Tuning radio stations Press button 6 until you hear a beep (the automatic...
Tape recorder — general information The radio is turned on by pressing the button 8, and the radio is switched to the tape recorder mode by pressing the button 12 "TARE". When a cassette is inserted, the radio automatically switches to tape recorder mode....
CD Player Switching to the CD player mode is carried out using the button 10 "CD". Insert the disc label-side up, being careful. Playback and stop are carried out by pressing the button 8 "PWR". To eject the disc, press button 9...
Parking system The parking system warns the driver of the presence of obstacles when parking the car. According to the dimensions of the car, sensors are installed that register obstacles. The zones of action of the sensors are shown...
Anti-lock braking system (ABS) Caution: Use tires of the same size, design and load capacity as the original tires on your vehicle, as using tires of a different type may interfere with the normal operation of the anti-lock braking system (ABS). 1....
Driving a car with automatic transmission To control the automatic transmission, a selector is installed on the center console. The selector is connected to the valve block by a cable, and with its help it is possible to set the range of gears used. To prevent...
Transmission features of 4WD models Attention: To avoid damage to the transmission components, 4WD models are not allowed to be towed using the partial load method (lifting only one of the vehicle axles). 4WD vehicles have permanent all-wheel drive, the...
Driving Tips for Various Conditions General recommendations Attention: Before driving, make sure that the parking brake is fully released and the corresponding indicator is off. Do not keep your foot on the brake pedal while driving. This can lead to...
Towing a car Attention: it is strictly forbidden to tow 4WD vehicles using the partial loading method, i.e. with raising one of the axles of the car. Attention: towing cars with automatic transmission is allowed at a speed of no...
Engine start Attention: do not allow prolonged operation of the engine at high speeds and sudden accelerations when the engine is cold. Before launch 1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. For...
Wheel replacement 1. If you need to change a wheel on the road, then gradually slow down and drive the car to a safe place. 2. Stop the vehicle on level ground with firm ground. 3. Stop the engine and turn on the hazard warning lights....
Tire pressure and condition check 1. Check tires regularly for damage. Check tire pressure every two weeks or at least once a month. Don't forget to check the spare tire pressure. The tire pressure recommended by TOYOTA for modifying your vehicle can be...
Tire change 1. When replacing tires, use only tires of the same size and design as originally installed, and with the same or greater load capacity. The use of any other size or type of tire can seriously affect handling, comfort,...
Features of the operation of aluminum wheels Caution: To avoid damage to the protective varnish layer, do not allow tire shop workers to clean the outer surface of the wheel with a metal brush and, when replacing adhesive balancing weights, remove them with a...
Replacing wheel discs 1. Due attention should be paid to the replacement of wheel disks. Make sure to install discs with the same load capacity, diameter, rim width and offset. 2. Incorrect wheel and tire selection can adversely affect...
Brake lining wear indicators Disc brake pads are equipped with wear indicators so that when driving, when the thickness of the pads is minimal, the wear indicator touches the brake disc and the brakes make an unpleasant sound (screech).
Catalytic converter and exhaust system 1. The catalytic converter is an emission control device. When operating a vehicle equipped with a converter, observe the following precautions: A) During and after engine operation, the exhaust pipe is heated to a high...
Checking and replacing fuses and fuses If the headlights or other electrical components do not work, then check the fuses and fuses. If any of the elements burned out, then it must be replaced. Fuses and fuses are sized to melt before all electrical wiring...