Vehicle owner's manual Toyota Duet

Vehicle identification
Vehicle Identification Number and Identification Plate The vehicle identification number, chassis number and identification plate are located as shown in the figure. 1 - identification table, 2 - vehicle identification...

Technical characteristics of engines installed on Toyota Duet and Daihatsu Sirion
Note: Power and torque values given are (j/S standard) are approximate and may vary depending on the specific modification and year of manufacture, but in most cases the error does not exceed ±5%.

Abbreviations and symbols
Abbreviations A/C - air conditioner ABS — anti-lock braking system ABV — air bypass valve AT (A/T) — automatic transmission CE - "check engine" indicator DIS — distributorless ignition system EVAP - Fuel Vapor Recovery...

General repair instructions
1. Use fender covers, seat covers and floor mats to protect your vehicle from dirt and damage. 2. When disassembling, arrange the parts in the proper order to facilitate subsequent assembly. 3. Observe the following...

Garage jack and lift paw mounting points
Jack mounting points Installation points for lift stands and paws

Main parameters of the car
Note: *¹ - models with 13-inch wheels. *² - models with 14-inch wheels. *³ - right mirror. * 4 - left mirror. * 5 - central seat. * 6 - side seats.

Door lock
Caution: When carrying out work in the passenger compartment of a vehicle equipped with an airbag system and seat belt pretensioners (sRS system), special care should be taken to avoid damaging the SRS control unit. To...

Odometer and trip meter
a) The odometer shows the total mileage of the vehicle. b) Odometers show the distance the vehicle has traveled since the last time the odometer was reset to zero. c) (Type 1) The "ODO/TRIP" button is used to switch...

Tachometer — General Information
The tachometer shows the number of revolutions of the engine crankshaft per minute (rpm). Note: While driving, watch the tachometer readings. Its needle, which shows the engine crankshaft speed, should not enter the red...

Fuel quantity indicator
The indicator shows the fuel level in the fuel tank (F - full tank, E - empty tank), when the ignition key is in the "ON" position. The low fuel indicator lights up when the fuel level in the tank is less than 6 liters....

Watches — General Information
When setting the time, the ignition key must be in the "ON" or "ACC" position. The time is set by turning the switch to the right or left. Turning the switch to the left ("H") sets the hour of the day. Turning the...

Instrument cluster indicators
1. Indicator of the parking brake system condition and brake fluid level. a) The indicator lights up if: parking brake engaged; low brake fluid level or brake booster leak; the electrical circuit of the indicator is...

Window lifters — general information
On models with electric window lifts, the position of the door windows is adjusted by pressing the corresponding switch. In this case, the key in the ignition switch must be set to the "ON" position. From the driver's...

Light signaling on the car
1. Turning on the side lights, headlights, instrument cluster and license plate lighting. Note: The headlight and turn signal switch operates regardless of the position of the key in the ignition switch. a) When you...

Flare — General Information
In Japan, to inform road users about a sudden breakdown in difficult weather conditions (in conditions of limited visibility) a flare is used. Note: After the expiration date, the flare should be disposed of, as its...

Hood — General Information
1. To open the hood, you must perform the following procedures: a) Pull up on the hood lock release lever as shown in the figure. b) Raise the hood slightly and pull the hood lock lever upward as shown in the figure. c)...

Back door
To open the rear door, insert the key into the lock, turn it clockwise and lift the door up. To open the rear door from inside the vehicle, pull up on the rear door lock actuator lever located as shown in the...

Filler neck hatch
To open the filler flap, pull up the lever located near the parking brake. Unscrew the fuel filler cap and install it in the holder located on the hatch.

Windscreen wiper and washer control
The wiper and washer control switch operates when the ignition switch is in the "ON" position. 1. To turn the cleaner on and off, move the switch to one of the positions: 1st position - complete stop; 2nd position -...

Rear door glass defroster switch
The rear door glass heater operates when the ignition key is in the "ON" position. If the rear door glass fogs up, press the top of the rear window defroster switch, located as shown in the figure. The heater's...

Mirror control
Mirror adjustment is performed from the mirror control panel. The ignition key must be in the "ON" or "ACC" position. The choice of control of the right or left mirror is made by setting the switch (1) to the...

Seats — General Information
1. Adjusting the longitudinal position of the front seats. To adjust the longitudinal position of the seats, move the lever up and move the seat to the desired position. After adjustment, return the lever to its...

Seat belts
To protect you and your passengers in the event of a traffic accident, it is recommended that all people in the vehicle wear seat belts. Attention: Do not wear the shoulder portion of the belt so that it passes under...

Precautions when operating vehicles equipped with the SRS system
The SRS airbags are designed only as a supplement to the primary safety belt system on the driver and front passenger sides. Driver's airbag. Front passenger airbag. Side airbag. Safety curtain. The driver and front...

Heater and air conditioner control
The operation of the air conditioner and heater is controlled from the control panel. 1. To turn on the heater, move the heater fan speed switch (2) from the "OFF" position to any other. To turn on the air conditioner,...

Radio tape recorder — main points of operation
Radio The quality of radio signal reception may vary significantly while the vehicle is moving due to terrain features, weather conditions and proximity to sources of electromagnetic radiation. Cassette player Clean the...

Anti-lock braking system (ABS)
Caution: Use tires of the same size, construction and load capacity as the original vehicle tires, as using a different type of tire may interfere with the proper operation of the anti-lock braking system (ABS). 1....

Electronic Brakeforce Distribution (EBD)
Please note: vehicles equipped with this system do not have a rear brake pressure regulator. 1. The use of electronic brake force distribution (EBD) instead of the rear axle load-dependent brake force distribution valve...

Traction Control System (TCS)
The traction control system (TRC) is designed to automatically prevent wheel slip during acceleration and driving on slippery surfaces, and ensures stable vehicle control. However, it should be borne in mind that on...

Vehicle Stability Control (VSC)
1. Vehicle Stability Control (VSC) automatically controls the output signals of the anti-lock brake system, traction control system or engine management system. It is designed to prevent the vehicle from skidding when...

Driving a car with automatic transmission
To control the automatic transmission, a selector is installed on the central console. The selector is connected to the valve block by a cable and allows you to set the range of gears used. To prevent breakdowns of the...

Driving a car with a manual transmission
The gear layout diagram is shown in the figure. The diagram is also depicted on the lever handle. Always fully depress the clutch pedal before changing gears. Attention: Do not keep your foot on the clutch pedal while...

Features of the transmission of 4WD models
Caution: To avoid damage to transmission components for 4WD models, do not: towing by partial loading method (by raising only one of the vehicle's axles); install tires of different types and sizes. 4WD models have...

Tips for driving in different conditions
General recommendations Attention: Before driving, make sure that the parking brake is fully released and the corresponding indicator is off. Do not keep your foot on the brake pedal while driving. This can lead to...

Ignition switch — «KEY FREE» system
This system allows you to start the car engine without using the ignition key. In models with the "KEY FREE" system, the key set includes a key card. When the driver with the key card is behind the wheel of the car, the...

Engine start — «KEY FREE» system
Caution: Do not allow the engine to run at high speed for a long time or accelerate sharply when not warmed up. 1. Apply the parking brake. 2. Turn off unnecessary lights and auxiliary equipment. 3. For models with...

If the engine does not start — the «KEY FREE» system
1. Before performing checks, make sure that the startup procedure has been performed correctly (see the relevant section) and the presence of sufficient fuel in the tank. 2. If the engine crankshaft does not turn or...

Starting the engine (if the spark plugs are «flooded») — «KEY FREE» system
1. While pressing the accelerator pedal, crank the engine with the ignition key in the "START" position for approximately 15 seconds. Do not pump the pedal, just hold it down. 2. Release the ignition key and the...

Starting with an additional battery — the «KEY FREE» system
Caution: The booster battery voltage must be 12 V. Do not jump start the engine with a booster battery unless you are sure that it meets the required parameters. 1. Turn off all unnecessary lights and make sure the cars...

Engine malfunctions while driving
Engine stops while driving 1. Reduce speed gradually. Move the car to a safe place. 2. Turn on the hazard warning lights. 3. Try to start the engine. Note: When the engine is not running, the brake and power steering...

Spare tire, jack and tools
The location of the jack, spare wheel and tool is shown in the figures. 1 - jack, 2 - spare wheel, 3 - tools. To remove the jack, rotate the handle counterclockwise until it is released. To install the jack into the...

Jacking up a car
1. Place the vehicle on a level and firm surface. 2. Stop the engine, apply the parking brake and block the wheel diagonally opposite the one to be replaced. 3. Insert the jack only into the designated places shown in...

Wheel replacement
1. If you need to change a tire on the road, gradually reduce speed and move the car to a safe place. 2. Stop the vehicle on a level place with firm ground. 3. Stop the engine and turn on the hazard warning lights. 4....

Recommendations for choosing tires
When choosing tires, pay attention to the marking. Geometric dimensions, load capacity and maximum speed must strictly comply with the manufacturer's recommendations. The landing diameter of the selected tire must...

Checking tire pressure and condition
1. Check your tires regularly for damage. Check your tire pressure every two weeks or at least once a month. Don't forget to check the pressure in your spare tire. The Toyota recommended tire pressure for your vehicle's...

Tire replacement
1. When replacing tires, use only tires of the same size and design as those originally installed, and with the same or greater load capacity. Using a tire of any other size or type may seriously affect handling,...

Features of using aluminum wheels
Caution: To avoid damaging the protective varnish layer, do not allow tire shop workers to clean the outer surface of the rim with a wire brush or remove adhesive balancing weights with a screwdriver when replacing...

Replacement of wheel disks
1. Due attention should be paid to replacing wheel rims. Make sure that rims with the same load capacity, diameter, rim width and offset are installed. 2. Incorrect selection of wheels and tires can adversely affect...

Brake pad wear indicators
Disc brake pads are equipped with wear indicators in such a way that when driving, when the thickness of the pads is minimal, the wear indicator touches the brake disc and the brakes make an unpleasant sound ("squeal").

Catalytic converter and exhaust system
1. The catalytic converter is a device for reducing the toxicity of exhaust gases. When operating a vehicle equipped with a catalytic converter, observe the following precautions: a) During and after engine operation,...

Checking and replacing fuses
If the headlights or other electrical components do not work, check the fuses. If any of the elements are burnt out, they must be replaced. Note: To remove and install type "A" fuses, use a special "tweezers" type...

Replacing lamps
When replacing a bulb, make sure the ignition and all lights are off. Use only bulbs with the rated power specified in the table.

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ User manual Toyota 4Runner N120 (1989-1995)
➥ User manual Toyota Camry XV10 (1991-1996)
➥ User manual Toyota RAV 4 XA20 (2000-2005)
➥ User manual Toyota Corona T190 (1992-1997)
➥ User manual Toyota Carina T190 (1992-1996)
➥ User manual Toyota Cruiser 70 (1985-1996, diesel)

Link in different formats to this article

TEXTHTMLBB Code