Engines 3S-FE, 3S-GE and 4S-FE cars Toyota Corona 9 (T190)

Description of petrol engines 3S and 4S
Engine 3S-FE. Engine 3S-GE. Engine 3S-GE. Engines 3S-FE, 3S-GE and 4S-FE in-line 4-cylinder, 16-valve overhead camshafts. The working volume of the 3S-FE, 3S-GE engines is 2.0 l, and the 4S-FE engine is 1.8 l. The...

Checking and adjusting the valve drive clearance
Note: Check and adjust the valve clearance on a cold engine. 1. (3SS-GE) Remove the intake chamber. a) Unscrew the four bolts and bracket No.2 of the intake chamber. b) Unscrew six bolts, two nuts, remove the intake...

Timing Belt (3S-FE, 4S-FE)
Removal the timing belt 1. Remove the right engine mount support by unscrewing the three bolts. 2 Remove the generator. a) Disconnect the wiring harness clamp from the clamp on the generator b) Disconnect the generator...

Adjustment of valve timing (3S-GE)
1. Remove the generator. 2. Remove the intake chamber. 3. Remove the spark plugs. 4. Remove timing belt cover No.2. 5. Check the timing marks of the camshaft toothed pulley. a) Turn the crankshaft pulley and align its...

Cylinder head (3S-FE, 4S-FE) — removal
Removal the cylinder head 1. Disconnect the negative terminal from the battery. 2. Drain the coolant from the cylinder block and radiator. 3. Disconnect the cables, remove the control cable mounting bracket by...

Cylinder head (3S-FE, 4S-FE) — installation
Installing the cylinder head 1. Install the cylinder head onto the cylinder block, after installing a new cylinder head gasket. 2. Install the cylinder head mounting bolts. Note: The cylinder head mounting bolts are...

Cylinder Head (3S-GE) — Removal
Removal and installation the cylinder head: 1 - valve of the variable geometry intake manifold system; 2 - gasket; 3 - intake manifold; 4 - right rear hook for lifting the engine; 5 - fuel manifold and injectors...

Cylinder Head (3S-GE) — Installation
Removal and installation the cylinder head: 1 - valve of the variable geometry intake manifold system; 2 - gasket; 3 - intake manifold; 4 - right rear hook for lifting the engine; 5 - fuel manifold and injectors...

Cylinder Block (3S-FE/GE, 4S-FE) — Disassembly and Assembly
Cylinder block; parts for disassembly and assembly. 1 - drain plug; 2 - gasket; 3 - oil pan; 4 - oil receiver 5 - oil separator; 6 - front crankshaft oil seal; 7 - main bearing; 8 - crankshaft; 9 - generator drive belt...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ 4-cylinder engine Toyota Camry XV30 (2001-2006)
➥ Petrol engines 1FZ-FE Toyota Cruiser 60/80 (1980-1997, petrol)
➥ Petrol engines 1.3 l Toyota Duet (1998-2004)
➥ 6-cylinder engines Toyota 4Runner N120 (1989-1995)
➥ Engine repair Toyota Corolla E80 (1983-1990)
➥ 4-cylinder engine Toyota Highlander 1 (2000-2007, petrol)

Link in different formats to this article

TEXTHTMLBB Code

Corona T190 (1992-1997)