Car steering Toyota Corona 9 (T190)

Checking the steering wheel play
With the vehicle stationary and the wheels set to the straight-ahead position, rock the steering wheel from side to side with a little effort. If the play exceeds the permissible limit, repair it. Maximum clearance is...

Checking the power steering pump drive belt
Press the belt with a force of 98 N, and measure the belt deflection. Drive belt deflection: A series engines: new: 5-6 mm used: 6-8 mm S series engines: new: 8-10 mm used: 10-13 mm C series engines: new: 11-16 mm used:...

Checking the working fluid level
1. Place the vehicle on a horizontal surface. 2. Warm up the working fluid. a) Start the engine and set it to idle speed. b) Turn the steering wheel several times from lock to lock to increase the temperature of the...

Checking the idle speed increase system
1. Warm up the engine to operating temperature. 2. Set the air conditioner switch to the "OFF" position. 3. Check the idle speed increase system. a) Turn the steering wheel all the way. b) Check that the rotation speed...

Replacing the power steering fluid
1. Raise the front of the vehicle and support it on stands. 2. Disconnect the return hose from the expansion tank and drain the working fluid into a container. 3. With the engine idling, turn the steering wheel from...

Bleeding the power steering system
1. Check the level of the working fluid in the tank. If necessary, add fluid. ATF DEXROtf II working fluid Note: If the working fluid is warm, the fluid level is in the "HOT" range on the tank or dipstick, if it is cold...

Checking the working fluid pressure
1. Connect the pressure gauge. a) (For vehicles with S-series engines) Using the special tool, disconnect the pressure line from the steering gear housing. b) (For other cars) Disconnect the discharge line from the pump...

Steering column — design description
Models up to 96) Steering column: 1 - intermediate shaft; 2 - anther; 3 - universal joint; 4 - steering column; 5 - Upper steering column cover; 6 - combination switch; 7 - steering wheel; 8 - steering wheel cover; 9 -...

Basic operations for removing and installing the steering column
(Models up to 96.) When removing and installing, refer to the assembly drawing. (For vehicles equipped with an airbag) 1. Remove the steering wheel cover. a) Using the special tool, loosen the SRS fuse bolt. b) Using...

Disassembling the tilt steering column
1. Remove the ignition switch bracket. a) Using a punch, mark the center of the cone head bolts. b) Drill a 3-4 mm diameter hole in the conical head bolts. c) Using a special tool, unscrew the bolts with conical heads...

Checking the tilt steering column
1. Check the ignition switch bracket. Check that the steering wheel lock mechanism works properly. 2. If necessary, replace the ignition lock cylinder. a) Set the ignition key to the "ACC" position. b) Press the locking...

Assembling a tilt steering column
1. Lubricate the surfaces of the parts indicated by the arrows in the figure with consistent grease. 2. Adopt the support bracket and tighten the 3 bolts. Tightening torque 19 Nm. 3. Install the main shaft. a) Using a...

Disassembling the steering column
1. Remove the universal joint. a) Apply alignment marks to the universal joint and main shaft. b) Unscrew the bolt. 2. Remove the bracket clamp and the ignition switch bracket. a) Using a punch, mark the center of the...

Checking the steering column
1. Check the ignition switch bracket. Check that the steering wheel lock mechanism works properly. 2. If necessary, replace the ignition lock cylinder. a) Set the ignition key to the "ACC" position. b) Press the locking...

Steering column assembly
Note: When using a vice, be careful not to damage the steering column. 1. Lubricate the surfaces of the parts indicated by arrows in the assembly drawing with consistent grease. 2. Install the main shaft and sleeve. a)...

Power steering pump
When removing and installing, refer to the assembly drawing. Power steering pump: 1 - Power steering pump, 2 - Gasket, 3 - Delivery pipe, 4 - Return hose, 5 - Adjustment bracket Power steering pump: 1 - drive belt, 2 -...

Checking the power steering pump
Caution: When using a vice, be careful not to damage the pump body. 1. Measure the clearance between the pump shaft and the housing sleeve. Oil clearance: standard: 0.01-0.03 mm maximum: 0.07 mm 2. Checking the rotor...

Removal the steering gear
Removal the steering gear: 1 - gasket, 2 - inlet pipe, 3 - clamp, 4 - engine mount central support beam, 5 - cross beam, 6 - pipe clamp bracket, 7 - discharge pipe, 8 - return hose, 9 - intermediate shaft No.2, 10 -...

Steering mechanism — design description
Steering gear type 1: 1 - tie rod end, 2 - lock nut, 3, 5 - clamp, 4 - tie rod boot, 6 - tie rod, 7 - toothed washer, 8 - oil seal, 9 - limiting sleeve, 10 - retaining ring, 11 - ring seal, 12 - Teflon ring, 13 - rack,...

Checking the steering gear
1. Checking the rack. c) Using an indicator, check the rack runout. Maximum runout is 0.3 mm. 6) Check the surface of the rack for wear and damage. 2. If necessary, replace the seal and bearing. a) Using a special tool,...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Steering Toyota Camry XV20 (1996-2001)
➥ Steering Toyota Corolla E80 (1983-1990)
➥ Steering Toyota Cruiser 70 (1985-1996, diesel)
➥ Steering Toyota 4Runner N120 (1989-1995)
➥ Steering Toyota Highlander 1 (2000-2007, petrol)
➥ Steering system Toyota RAV 4 XA20 (2000-2005)

Link in different formats to this article

TEXTHTMLBB Code

Corona T190 (1992-1997)