Share information:
Gasoline engines 1FZ-FE Toyota Land Cruiser 60/80
This subsection describes the types of repair of a 6-cylinder in-line 1FZ-FE engine without dismantling it from the vehicle.
The engine has been installed on cars since 1993. The engine is two-shaft, with overhead valves. Camshaft drive - from the chain. Each cylinder has 2 intake and exhaust valves. The left camshaft (in the direction of the car) controls the intake valves, and the right camshaft controls the exhaust valves.
All engines of this type are equipped with an electronic fuel injection system.
Technical characteristics of 1FZ-FE engines
Cylinder numbering order and direction of rotation of the distributor of FZ-FE 1 engines The dark circle marks the output of the 1st cylinder of the ignition distributor. Working volume 4.5 l Cylinder numbering...
Cylinder numbering order and direction of rotation of the distributor of FZ-FE 1 engines The dark circle marks the output of the 1st cylinder of the ignition distributor. Working volume 4.5 l Cylinder numbering...
Types of repairs without engine dismantling
Without removing the engine from the vehicle, the following work can be performed: replace gaskets and seals; remove mounted units and assemblies for replacement or repair; carry out repairs (or replacement) cylinder...
Without removing the engine from the vehicle, the following work can be performed: replace gaskets and seals; remove mounted units and assemblies for replacement or repair; carry out repairs (or replacement) cylinder...
Cylinder Head Cover — Removal and Installation
Removal 1. Disconnect the battery from ground. 2. Remove the air intake, disconnect the crankcase ventilation hoses from the cover. 3. Remove the spark plug caps and disconnect the wires. 4. Disconnect the throttle and...
Removal 1. Disconnect the battery from ground. 2. Remove the air intake, disconnect the crankcase ventilation hoses from the cover. 3. Remove the spark plug caps and disconnect the wires. 4. Disconnect the throttle and...
Intake manifold — removal and installation
Caution! If the manifold is disconnected only to remove the cylinder head, then unscrew the bolts and move it to the side without disconnecting the hoses and wires. The procedure for dismantling the manifold from the...
Caution! If the manifold is disconnected only to remove the cylinder head, then unscrew the bolts and move it to the side without disconnecting the hoses and wires. The procedure for dismantling the manifold from the...
Exhaust manifold — removal and installation
Attention! Work is performed on a cold engine. Removal 1. Disconnect the battery from ground. 2. On engines equipped with a PAIR system (pulse fuel injection system) remove the system of pipes and valves located near...
Attention! Work is performed on a cold engine. Removal 1. Disconnect the battery from ground. 2. On engines equipped with a PAIR system (pulse fuel injection system) remove the system of pipes and valves located near...
Camshafts and tappets — removal, inspection and installation
Attention! Before performing the work, prepare two bolts with a 6x1 mm thread and a length of 16–20 mm, which will be used as auxiliary ones during disassembly (see below). Removal 1. Remove the cylinder head cover (see...
Attention! Before performing the work, prepare two bolts with a 6x1 mm thread and a length of 16–20 mm, which will be used as auxiliary ones during disassembly (see below). Removal 1. Remove the cylinder head cover (see...
Cylinder head — removal and installation
Attention! Work is performed on a cold engine. Removal 1. Disconnect the battery from ground. 2. Drain the coolant. 3. Drain the engine oil and remove the oil filter. 4. Remove the throttle body, fuel distributor and...
Attention! Work is performed on a cold engine. Removal 1. Disconnect the battery from ground. 2. Drain the coolant. 3. Drain the engine oil and remove the oil filter. 4. Remove the throttle body, fuel distributor and...
Camshaft Chain Cover — Removal, Inspection and Installation
Front engine parts 1. Compressor; 2. Bracket; 3. Pallet 1; 4. Oil level sensor; 5, 7. Gaskets; 6. Pallet 2; 8. Lower shield; 9. Tensioner roller; 10. Pulley; 11. Belt adjustment bar; 12. Ring; 13. Front oil seal; 14....
Front engine parts 1. Compressor; 2. Bracket; 3. Pallet 1; 4. Oil level sensor; 5, 7. Gaskets; 6. Pallet 2; 8. Lower shield; 9. Tensioner roller; 10. Pulley; 11. Belt adjustment bar; 12. Ring; 13. Front oil seal; 14....
Front Crankshaft Oil Seal — Replacement
1. Remove the belts and crankshaft pulley. 2. Determine the depth of pressing the seal, then carefully remove the seal from the oil pump housing, prying it with a screwdriver or special tool. 3. It is also possible to...
1. Remove the belts and crankshaft pulley. 2. Determine the depth of pressing the seal, then carefully remove the seal from the oil pump housing, prying it with a screwdriver or special tool. 3. It is also possible to...
Oil pan — removal and installation
Removal 1. Disconnect the battery from ground. 2. Set the car's handbrake and block the rear wheels. 3. Raise the front of the car. 4. Remove the engine mudguards. 5. Drain the oil and remove the oil filter. Remove the...
Removal 1. Disconnect the battery from ground. 2. Set the car's handbrake and block the rear wheels. 3. Raise the front of the car. 4. Remove the engine mudguards. 5. Drain the oil and remove the oil filter. Remove the...
Oil pump — removal, inspection and installation
Oil pump parts 1. Pump (front cover); 2. Spring; 3. Plug; 4. Gasket; 5. Pressure reducing valve; 6. Gasket; 7. Slave rotor; 8. Leading rotor; 9. Pump cover; 10. Crankshaft oil seal Removal 1. Remove the belts and...
Oil pump parts 1. Pump (front cover); 2. Spring; 3. Plug; 4. Gasket; 5. Pressure reducing valve; 6. Gasket; 7. Slave rotor; 8. Leading rotor; 9. Pump cover; 10. Crankshaft oil seal Removal 1. Remove the belts and...
Flywheel (torque converter drive disk)
Removal 1. Disconnect the battery from ground. Raise the vehicle and place it on stands. Remove the transmission (gearbox). 2. Remove the clutch. 3. Mark the position of the flywheel relative to the crankshaft. 4....
Removal 1. Disconnect the battery from ground. Raise the vehicle and place it on stands. Remove the transmission (gearbox). 2. Remove the clutch. 3. Mark the position of the flywheel relative to the crankshaft. 4....
Rear Crankshaft Oil Seal — Replacement
1. Remove the gearbox (transmission). Remove the back plate. 2. The seal can be removed without dismantling the oil pan or removing the seal holder. However, this method is not recommended, since the seal is installed...
1. Remove the gearbox (transmission). Remove the back plate. 2. The seal can be removed without dismantling the oil pan or removing the seal holder. However, this method is not recommended, since the seal is installed...
Suspension and Engine Parts — Checking and Replacing
Engine mount components generally do not require maintenance, however, if damage to the engine mounts or signs of aging are detected, they should be replaced immediately. Examination 1. Raise the vehicle and support it...
Engine mount components generally do not require maintenance, however, if damage to the engine mounts or signs of aging are detected, they should be replaced immediately. Examination 1. Raise the vehicle and support it...
Starter motor — removal, inspection and installation
Starter mounting details 1. Connector 2. Wire 3. Starter Checking without removing from the vehicle 1. If the starter motor does not turn at all when you turn the key, make sure the selector lever is in the Park or...
Starter mounting details 1. Connector 2. Wire 3. Starter Checking without removing from the vehicle 1. If the starter motor does not turn at all when you turn the key, make sure the selector lever is in the Park or...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other Toyota models
➥ Petrol engines Toyota Camry Vista V40 (1994-1998)
➥ Petrol engines 1.3 l Toyota Duet (1998-2004)
➥ Engines 3S-FE/GE and 4S-FE Toyota Corona T190 (1992-1997)
➥ Engine repair Toyota Corolla E80 (1983-1990)
➥ 4-cylinder engines Toyota 4Runner N120 (1989-1995)
➥ 4-cylinder engine Toyota Highlander 1 (2000-2007, petrol)
Link in different formats to this article
TEXTHTMLBB Code
- General information
- Introduction to the guide
- Controls and instruments
- Maintenance
- Power unit
- Petrol engines
- Diesel engines
- Cooling and heating
- Power and exhaust systems
- Engine electrical equipment
- Engine management systems
- Transmission
- Automatic gearbox
- Transmission line
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines 2F and 3F-E
- Petrol engines 1FZ-FE
- Engine overhaul
- Engine electrical equipment
- Cooling and heating
- Fuel system (carburetor)
- Fuel system (injector)
- Toxicity reduction system
- Transmission
- Car gearbox
- Clutch
- Transfer case
- Drive shafts and axles
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior and interior
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Engine adjustment
- Engine repair
- Fuel system
- Control system
- Turbocharging system
- Cooling and lubrication system
- Charge and start system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Chassis, running gear
- Car suspension
- Brake system
- Steering
- Body and interior
- Body elements
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Electrical circuits