Car front suspension Toyota Corona 9 (T190)

Preliminary suspension checks
Note: The term "heavy-duty suspension" refers to the suspension of vehicles equipped with the "rough road package". 1. Check tire wear and tire pressure when cold. 2. Check the axial clearance of the hub bearings. 3....

Adjusting the front wheel alignment angles
Checking and adjusting the alignment Check the toe-in value. If it does not meet the specified conditions, make adjustments. Convergence during inspection: Models up to 96: A + B = 0°±0.2° C - D = 0±2 mm Models since...

Front suspension — design description
Front suspension: 1 - upper support of the rack, 2 - front suspension rack, 3 - anti-roll bar, 4 - lower arm, 5 - spring

Front Axle Hub — Design Description
Front axle hub: 1, 2, 11 - cotter pin, 3 - lock nut cap, 4 - brake disc, 5 - hub, 6 - hub bolt, 7, 16 - oil seal, 8, 14 - bearing inner ring, 9 - mud guard, 10 - lower ball joint, 12 - steering knuckle, 13 - bearing, 15...

Removal the steering knuckle with the hub
1. Jack up the car, remove the front wheel. 2. Check the bearing axial clearance and hub runout. a) Unscrew the two bolts and remove the caliper assembly. b) Hang the caliper assembly on the wire. c) Remove the brake...

Disassembling the front axle hub
1. Using a screwdriver, remove the dust cover. 2. Using a special tool, remove the inner oil seal. 3. Remove the lower ball joint. a) Remove the cotter pin and unscrew the nut. b) Using a puller, remove the lower ball...

Front axle hub assembly
1. Install the bearing a) Using a special tool and a press, install a new bearing into the steering knuckle. 6) Using the special tool, install the new retaining ring. 2. Install the mudguard and tighten the 4 bolts....

Installing the steering knuckle with the hub
1. Install the steering knuckle. a) Install the steering knuckle and temporarily install the two bolts. Note: Apply engine oil to the nut threads. b) Connect the lower ball bolt and two nuts. Tightening torque 127 Nm....

Replacing the hub bolt
1. Jack up the car, remove the front wheel. 2. Remove the caliper assembly and brake disc. 3. Using a special tool, unscrew the hub bolt. 4. Install the hub bolt. a) Install the washer and nut onto the hub bolt as shown...

Front suspension strut — design description
Front suspension strut (Models up to 96.): 1 - plug, 2 - upper support of the strut, 3 - seal, 4 - upper spring seat, 5 - upper vibration isolator, 6 - front suspension strut, 7 - lower vibration isolator, 8 -...

Removal the front suspension strut
1. Jack up the car, remove the front wheel. 2. (For cars with ABS) Remove the brake hose and speed sensor (ABS) wire from the rack. 3. Disconnect the strut from the steering knuckle by unscrewing the bolts and nuts. 4....

Assembly and installation of the front suspension strut
1. Install the lower vibration isolator on the stand. 2. Install the spring compression stroke limiter onto the piston rod. 3. Install the spring, a) Using the special tool, compress the spring. b) Install the spring on...

Lower control arm of the front suspension — description of the design
Lower control arm of the front suspension (Models up to 96.): 1 - central engine mount beam, 2 - cross beam, 3, 5 - cotter pin, 4 - lock nut cap, 6 - lower arm, 7, 9 - gasket, 8 - exhaust pipe Lower control arm of the...

Removal the lower arm
1. Jack up the car, remove the front wheel. 2. Remove the engine protection. 3. (Models since 1996.) Remove the exhaust pipe. a) Unscrew the two bolts and remove the exhaust gas temperature sensor and gasket. b) Unscrew...

Installing the lower control arm
1. (Models up to 96.) Models with automatic transmission (left side) Install the left lower control arm. (Models since 1996.) Install the lower arm. a) Install the sleeve holder and tighten the bolt. Tightening torque 8...

Lower ball joint — design description
Lower ball joint: 1 - dust cover, 2, 3 - cotter pin, 4 - lock nut cap, 5 - brake disc, 6 - lower ball joint, 7 - caliper assembly

Removal the lower ball joint
1. Remove the steering knuckle assembly with the hub. 2. Remove the ball joint. a) Using a screwdriver, remove the dust cover. b) Remove the cotter pin and nut. c) Using a puller, remove the ball joint.

Checking the lower ball joint
Check the ball joint rotation moment. a) Before installing the nut, rock the ball joint axle from side to side 5 times. b) Using a torque wrench, rotate the nut continuously (one revolution in 2-4 seconds) and take a...

Installing the lower ball joint
1. Install the ball joint. a) Install the ball joint and tighten the nut. Tightening torque 123 Nm. b) Install a new cotter pin. 2. Using the special tool and a hammer, install the new boot. Note: Align the holes for...

Anti-roll bar — design description
Anti-roll bar: 1 - transverse stability stabilizer, 2 - bracket of transverse stability stabilizer, 3 - bushing, 4 - strut of transverse stability stabilizer, 5 - cotter pin, 6 - gasket, 7 - muffler intake pipe, 8 -...

Removal the anti-roll bar
1. Jack up the car, remove the front wheels. 2. (Models up to 96.) Remove the cross beam. (Models since 1996.) a) Remove the steering knuckle with the hub b) Unscrew the four nuts and remove the stabilizer struts. Note:...

Checking the anti-roll bar
Check the rotation moment of the stabilizer bar ball joint. a) Before installing the nut, rock the ball joint axle from side to side 5 times. b) Using a torque wrench, rotate the nut continuously (one revolution in 2-4...

Installing the anti-roll bar
1. Install the left and right anti-roll bar bushings. a) Install the bushings. Note: (Models since 1996.) install the bushings with the mark facing outward. b) Install the bushing brackets and tighten the bolts....

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Front suspension Toyota Carina T170 (1988-1992)
➥ Front suspension Toyota Camry Vista V40 (1994-1998)
➥ Front suspension Toyota Corolla E80 (1983-1990)
➥ Front suspension Toyota RAV 4 XA20 (2000-2005)

Link in different formats to this article

TEXTHTMLBB Code

Corona T190 (1992-1997)