Share information:
Exhaust system cars Corolla Verso 3 (AR10)
Intake and exhaust systems 1ZZ-FE and 3ZZ-FE — design description
Fig. 2.18. Intake and exhaust system of 1ZZ-FE and 3ZZ-FE engines To reduce weight and heat from the cylinder head, the intake manifold is made of plastic. As a result, it was possible to reduce the air temperature at...
Fig. 2.18. Intake and exhaust system of 1ZZ-FE and 3ZZ-FE engines To reduce weight and heat from the cylinder head, the intake manifold is made of plastic. As a result, it was possible to reduce the air temperature at...
CD-FTV intake and exhaust system — design description
Fig. 2.74. Engine intake and exhaust system 1CD-FTV The engine is equipped with an intake manifold with channels of equal length and a receiver to reduce turbulence of the air flow distributed among the cylinders. The...
Fig. 2.74. Engine intake and exhaust system 1CD-FTV The engine is equipped with an intake manifold with channels of equal length and a receiver to reduce turbulence of the air flow distributed among the cylinders. The...
Checking without removing from the vehicle
Checking the air intake system Check that the passage between the air filter housing and the turbocharger inlet and between the turbocharger outlet and the cylinder head is tight and free of blockages. Checking the...
Checking the air intake system Check that the passage between the air filter housing and the turbocharger inlet and between the turbocharger outlet and the cylinder head is tight and free of blockages. Checking the...
Replacing the intercooler assembly (1CD-FTV)
Disconnect the negative battery terminal. Remove the lower left engine shield. Remove the upper radiator shroud. Remove the radiator grille. Remove the front bumper cover. Removal the intercooler duct Fig. 2.431....
Disconnect the negative battery terminal. Remove the lower left engine shield. Remove the upper radiator shroud. Remove the radiator grille. Remove the front bumper cover. Removal the intercooler duct Fig. 2.431....
Checking the Vacuum Distribution Valve (VRV) Assembly
Check the resistance. Fig. 2.436. Resistance testing Use an ohmmeter to measure the resistance between the terminals (fig. 2.436). Verification conditions If the resistance is not within the nominal value, replace the...
Check the resistance. Fig. 2.436. Resistance testing Use an ohmmeter to measure the resistance between the terminals (fig. 2.436). Verification conditions If the resistance is not within the nominal value, replace the...
Boost Pressure Sensor Replacement (1CD-FTV)
Disconnect the negative battery terminal. Remove the upper engine cover No.1. Fig. 2.440. Sensor connector Disconnect the connector and hose (fig. 2.440). Fig. 2.441. Sensor mounting Unscrew 2 nuts, then remove the...
Disconnect the negative battery terminal. Remove the upper engine cover No.1. Fig. 2.440. Sensor connector Disconnect the connector and hose (fig. 2.440). Fig. 2.441. Sensor mounting Unscrew 2 nuts, then remove the...
Replacing the VRV Vacuum Distribution Valve Assembly (1CD-FTV)
Disconnect the negative battery terminal. Remove the upper engine cover No.1. Fig. 2.442. VSV valve connector Disconnect the connector and 2 hoses (fig. 2.442). Fig. 2.443. Fastening of the VSV valve Remove 2 nuts then...
Disconnect the negative battery terminal. Remove the upper engine cover No.1. Fig. 2.442. VSV valve connector Disconnect the connector and 2 hoses (fig. 2.442). Fig. 2.443. Fastening of the VSV valve Remove 2 nuts then...
Removal and installation the exhaust pipe assembly (1ZZ-FE / 3ZZ-FE)
Fig. 2.612. Exhaust pipe assembly (1ZZ-FE/ 3ZZ-FE) Fig. 2.613. Exhaust pipe assembly (1CD-FTV) Disconnect the negative terminal from the battery post. Remove the front footrest. Remove the heated oxygen sensor. Removal...
Fig. 2.612. Exhaust pipe assembly (1ZZ-FE/ 3ZZ-FE) Fig. 2.613. Exhaust pipe assembly (1CD-FTV) Disconnect the negative terminal from the battery post. Remove the front footrest. Remove the heated oxygen sensor. Removal...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this article
TEXTHTMLBB Code
- General information
- User manual
- Start of movement
- Faults en route
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Supply system
- Fuel supply (carburetor)
- Fuel supply (injector)
- Diesel engine
- Exhaust system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Interior heating
- Electrical equipment
- Equipment and devices
- Power devices
- Lighting system
- Glass cleaners and washers
- General information
- User manual
- Power unit
- Petrol engines 1ZZ, 3ZZ
- Diesel engines 1СD-FTV
- Cooling system
- Lubrication system
- Fuel system
- Control system
- Exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Electrical equipment
- Power devices
- Electrical circuits