Braking system cars Corolla Verso 3 (AR10)

Car braking system — general information
Fig. 6.1. Components of the braking system of the Corolla Verso The new models use two types of braking systems: ABS with electronic brake-force distribution (EBD) and ABS with electronic brake-force distribution (EBD),...

ABS with Electronic Brakeforce Distribution (EBD)
Fig. 6.2. Block diagram of ABS with electronic brake force distribution (EBD) system The braking system of new models (ABS with electronic brake force distribution (EBD)) performs the following functions. Maintenance...

Electronic Brakeforce Distribution (EBD)
Fig. 6.3. Location of the main components of the electronic brake force distribution (EBD) system The mechanical brake force distribution system used on previous models has given way to an electronic control unit (ECU)...

Bleeding the brake circuit
Note: The brake system should be bled after repair work or if there is a suspicion of air in the brake lines. Fig. 6.6. Filling the expansion tank with brake fluid Fill the expansion tank with brake fluid (Fig. 6.6)....

Adjusting the brake pedal
Checking and adjusting the height of the brake pedal Fig. 6.10. Brake pedal height Check the height of the brake pedal (Fig. 6.10). Brake pedal height from engine compartment bulkhead: for left-hand drive: manual...

Checking the brake booster assembly
Checking for leaks Fig. 6.14. Checking the brake booster Start the engine and turn it off after 1 or 2 minutes. Slowly press the brake pedal at least 3 times (Fig. 6.14). Note: The brake booster is sealed if the...

Checking the Vacuum Pump Assembly (1CD-FTV)
Checking functionality Remove the clamp, disconnect the vacuum hose from the vacuum pump. Fig. 6.17. Checking the vacuum pump assembly Connect the vacuum sensor hose to the vacuum pump assembly as shown in Figure 6.17....

Checking the brake actuator assembly (without VSC)
Connecting the Portable Diagnostic Tool II Connect the Portable Diagnostic Tool II to the DLC3 connector. Start the engine and let it idle. In the Portable Diagnostic Tool II, select the mode "ACTIVE TEST" ("ACTIVE...

Checking the ABS and PBS actuator (with the VSC stability control system)
Connecting the Portable Diagnostic Tool II Connect the Portable Diagnostic Tool II to the DLC3 connector. Start the engine and let it idle. In the Portable Diagnostic Tool II, select the mode "ACTIVE TEST" ("ACTIVE...

Adjusting the parking brake
Remove the rear wheel. Adjust the parking brake shoe clearance. Install the rear wheel. Tightening torque: 103 Nm. Checking the travel of the parking brake lever Fully tighten the parking brake lever and count the...

Replacing the parking brake lever
Fig. 6.19. Parking brake components Removal the top console panel Fig. 6.20. Console top panel fasteners Using a screwdriver, release the 4 fasteners and remove the top panel of the console (Fig. 6.20). Note: Wrap the...

Replacing the parking brake drive cable No. 1 in assembly
Remove the top panel of the console. Remove the rear end panel of the console. Remove the storage box on the console. Remove the parking brake lever. Removal Disconnect parking brake cable No.1 from parking brake cables...

Replacing the front brake pads
Fig. 6.25. Front brake components Removal brake pads Drain the brake fluid. Caution: When replacing brake pads, always replace the inner pads, outer pads and pad covers as a set. Remove the front wheel and temporarily...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Brake system Toyota 4Runner N120 (1989-1995)
➥ Brake system Toyota Highlander 1 (2000-2007, petrol)
➥ Brake system Toyota Cruiser 100 (1998-2007)
➥ Brake system Toyota Corona T190 (1992-1997)
➥ Brake system Toyota Carina T190 (1992-1996)
➥ Brake system Toyota Duet (1998-2004)

Link in different formats to this article

TEXTHTMLBB Code