Diesel engines 2C car Toyota Carina 6 (T190)

Checking and adjusting thermal clearances in valves
Note: Checking and adjusting thermal clearances in valves is carried out on a cold engine. 1. Disconnect the accelerator cable from the bracket. 2. Disconnect the wiring harness. 3. Disconnect the vacuum tubes. 4....

Timing belt — device
1 - right engine support, 2 - washer reservoir, 3 - power steering pump, 4 - power steering pump drive belt, 5 - power steering pump pulley, 6 - timing belt cover No.2, 7 - gasket, 8 - timing belt, 9 - timing belt...

Removal the timing belt
1. Remove the right side of the engine guard. 2. Remove the washer reservoir. 3. Remove the power steering pump drive belt. 4. Remove the power steering pump. a) Disconnect the hydraulic tube clamp. b) Remove the power...

Installing the timing belt
1. Install the crankshaft timing pulley. a) Align the keyway on the pulley with the key on the front nose of the crankshaft. b) Using a special mandrel (or a tube of suitable diameter) and a hammer, seat the toothed...

The structure of the cylinder head, timing belt and cylinder head cover (2C)
1 - power steering pump, 2 - power steering pump pulley, 3 - power steering pump drive belt, 4 - vacuum tubes, 5 - washer reservoir, 6 - right engine support, 7 - cylinder head cover assembly with vacuum pump, 8 -...

Removal the cylinder head
1. Disconnect the negative terminal from the battery. 2. Drain the coolant. 3. Disconnect the exhaust pipe. 4. Disconnect the accelerator cable from the bracket. 5. Disconnect the vacuum tubes. 6. Disconnect the wiring...

Cylinder head assembly (2C). Dismantling the cylinder head
1 - cylinder head assembly, 2 - washer, 3 - high pressure tubes, 4 - drainage tube, 5 - air filter cover with air duct, 6 - gasket, 7 - coolant outlet pipe, 8 - exhaust gas recirculation (EGR) tube, 9 - coolant bypass...

Replacing camshaft seals
Note: There are two ways to replace the oil seal, depending on whether the camshaft oil seal housing has been removed or not. 1. With the removal of the camshaft oil seal housing from the cylinder head. a) Unscrew the 4...

Installing the cylinder head
Note: - Thoroughly clean all parts to be installed. - Before installing parts, lubricate all rotating and sliding surfaces with oil. - Replace all gaskets and seals with new ones. 1. Install the camshaft. a) Install the...

Preparing for disassembling the cylinder block
1. Remove the flywheel or torque converter drive plate (see section " Cylinder block " chapters " Petrol engines 4A-FE, 5A-FE, 7A-FE "). 2. Place the engine on the disassembly stand. 3. Remove the timing belt and...

Final assembly of the cylinder block
1. Install the oil filter with bracket. 2. Install the oil pump and oil pan (see chapter " Smear system "). 3. Install the generator assembly. 4. Install the coolant pump (see chapter " Cooling system "). 5. Install the...

Cylinder block device (2C)
1 - compression rings, 2 - oil scraper ring, 3 - piston pin, 4 - piston, 5 - retaining ring, 6 - connecting rod piston head bushing, 7 - connecting rod, 8 - connecting rod bearing shell, 9 - connecting rod cover, 10 -...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Diesel engines 1СD-FTV Toyota Corolla Verso 3 (2004-2009)
➥ Diesel engines Toyota Cruiser 100 (1998-2007)
➥ Fuel system (diesel) Toyota Corona T190 (1992-1997)
➥ Diesel engines Toyota RAV 4 XA20 (2000-2005)
➥ Diesel engines Toyota Camry Vista V40 (1994-1998)

Link in different formats to this article

TEXTHTMLBB Code