Exterior (external elements) of the body Toyota Carina 6 (T190)

Holders (pistons) — removal and installation
If holders (pistons) are used when fastening parts, be guided by the corresponding drawings when taking them off and installing them (see legend in the pictures).

Front bumper — removal and installation
When removing and installing the front bumper, refer to the corresponding assembly drawing. Front bumper 1 - front dimensions, 2 - mudguard, 3 - radiator grille, 4 - bumper cover, 5 - parking sensor, 6 - direction...

Adjusting the hood
Note: The hood and its lock cannot be adjusted when the hood and lock are secured with centering bolts. When adjusting, these bolts should be replaced with regular bolts and washers. 1. Adjustment of the hood in...

Rear bumper — removal and installation
When removing and installing the rear bumper, refer to the corresponding assembly drawing. Rear bumper 1 - mudguard, 2 - rear trunk trim, 3 - parking sensor, 4 - upper rear bumper holder, 5 - side mount of the bumper...

Adjustment of front and rear side doors
1. Adjust the gap between the body and the doors (see figure: "Adjusting the gap between the body and the side doors"). Adjusting the gap between the body and the side doors 2. Adjusting the door in longitudinal and...

Front door device
1 - side outside rear view mirror, 2 - door glass, 3 - external door opening handle, 4 - lock cylinder, 5 - glass seal, 6 - decorative plug, 7 - inner cover of the side exterior mirror, 8 - outer cover of the side...

Disassembling the front side doors
1. (Models without electric windows). Remove the window lift handle as shown in the figure below. 2. (Models with electric windows). Remove the driver's side power window control panel. 3. (Models with electric...

Assembly of front side doors
Assembly of the front side doors is carried out in the reverse order of disassembly, with the following exceptions: a) Before installation, apply glue to the door lock mounting screws as shown in the figure. b) The...

Rear door device
1 - door glass, 2 - rear fixed door glass, 3 - rear fixed door glass seal, 4 - door glass seal, 5 - rear door glass guide, 6 - external door opening handle, 7 - lock rod, 8 - internal locking rod, 9 - electric door...

Disassembling the rear side doors
1. (Models without electric windows). Remove the window lift handle. 2. (Models with electric windows). Remove the power window control panel. 3. Remove the decorative trim from the inner door handle. 4. (Models with...

Assembling the rear side doors
The rear side doors are assembled in the reverse order of disassembly, with the following exceptions: a) Before installation, apply glue to the door lock mounting screws as shown in the figure. b) The tightening torque...

Removal the rear spoiler
1. Remove the inner trim of the trunk lid. 2. Unscrew the two nuts securing the rear spoiler. 3. Stick the adhesive tape on the outer surface of the trunk lid as shown in the figure. 4. Using a lamp, heat the attachment...

Disassembling and assembling the rear spoiler
When disassembling and assembling the rear spoiler, refer to the assembly drawing: "Rear spoiler". Rear spoiler 1 - rear spoiler assembly, 2 - inner lining of the trunk lid, 3 - upper cover of the rear spoiler, 4 -...

Installing a rear spoiler
1. Clean the rear spoiler installation areas from adhesive residue using a scraper or a rag soaked in solvent. 2. Apply a new layer of adhesive to the connecting surfaces as shown in the figure. 3. Using a lamp, heat...

Removal and installation the trunk lid
When removing and installing the trunk lid, refer to the corresponding assembly drawing. 1 - central torsion bar bracket, 2 - right torsion bar, 3 - left torsion bar, 4 - rear trim, 5 - inner lining of the trunk lid, 6...

Adjusting the trunk lid
1. Adjust the gap between the trunk lid and the car body as shown in the figure. 2. Adjust the position of the trunk lid in the longitudinal and transverse directions by loosening the mounting bolts to the car body. 3....

Removal and installation the torsion bar
Removal Removal and installation of the torsion bar is carried out in the following order: 1. Disconnect the torsion bar from the center bracket. 2. Install the special tool on the torsion bar from the trunk lid hinge...

Windshield device
1 - glass molding, 2 - windshield, 3 - glass seal, 4 - sun visor, 5 - interior mirror, 6 - front light (models without sunroof), 7 - sunroof control panel and front light assembly (models with sunroof), 8 - handle, 9 -...

Removal the windshield
1. Remove the following parts: a) Windscreen wiper arms. b) Seal and ventilation grille of the hood. c) Sun visors. d) Interior mirror. d) (Models with hatch). Sunroof control panel and front light assembly. e) Upper...

Windshield installation
1. Align and clean the contact surface of the body. a) Use a knife to level the layer of glue remaining on the body, be careful not to damage the paintwork of the body. b) Clean the cut surface on the body with a piece...

Removal the rear window
The rear window removal procedures are similar to the corresponding windshield removal procedures, with the design differences listed below. 1. Remove the following parts: a) Remove the rear seat cushion and backrest....

Rear window device
1 - glass seal, 2 - rear window, 3 - rear window molding, 4 - lower molding, 5 - clamp, 6 - windshield wiper arm, 7 - upper cover of the windshield wiper motor, 8 - washer nozzle, 9 - lower cover of the windshield wiper...

Installing the rear window
The rear window installation procedures are similar to the corresponding windshield installation procedures, with the design differences listed below. 1. Align and clean the contact surface of the body. a) Use a knife...

Hatch device
1 - sunroof glass, 2 - hatch seal, 3 - interior rear hatch trim, 4 - inner front hatch trim, 5 - connecting bracket, 6 - side frame of the drive cable guide, 7 - limiter, 8 - inner side trim of the hatch, 9 - deflector...

Adjusting the hatch
1. Check that the front edge of the hatch is positioned correctly. a) Check the height of the sunroof relative to the roof of the car, as shown in the figure. b) Check the width of the hatch seal as shown in the figure....

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Exterior (external elements) Toyota Cruiser 100 (1998-2007)
➥ Exterior (external elements) Toyota 4Runner N120 (1989-1995)
➥ Exterior (external elements) Toyota Corolla Verso 3 (2004-2009)
➥ Exterior (external elements) Toyota Camry XV20 (1996-2001)
➥ Exterior (external elements) Toyota RAV 4 XA20 (2000-2005)
➥ Exterior (external elements) Toyota Highlander 1 (2000-2007, petrol)

Link in different formats to this article

TEXTHTMLBB Code