Car engine lubrication system Toyota Carina 6 (T190)

Checking oil pressure
1. Check the engine oil level. 2. Disconnect the negative terminal from the battery. 3. Preliminary operations. (A series engines) a) Remove the right side of the engine guard. b) Remove the air conditioning compressor....

Oil pan and oil pump design (4A-FE, SAFE)
1 - oil dipstick, 2 - oil dipstick guide, 3 - crankshaft position sensor (4A-FE), 4 - O-ring seal, 5 - tensioner roller spring, 6 - timing belt tensioner roller, 7 - toothed pulley of the crankshaft, 8 - oil seal, 9 -...

Oil Pump and Oil Pan (4A-FE, 5A-FE, 7A-FE) — Removal
1. Drain the oil from the engine. 2. (7A-FE) Remove the left side of the engine guard. 3. Remove the timing belt. 4. (7A-FE) Remove the adjusting bar by unscrewing the 3 mounting bolts. 5. (4A-FE, 7A-FE) Disconnect the...

Oil pan and oil pump assembly (7A-FE)
1 - oil dipstick, 2 - oil dipstick guide, 3 - crankshaft position sensor, 4 - O-ring seal, 5 - timing belt tensioner roller, 7 - oil seal, 8 - oil pump, 9 - gasket, 10 - adjustment bar, 11 - upper part of the oil pan,...

Oil Pump and Oil Pan (4A-FE, 5A-FE, 7A-FE) — Installation
1. Install the oil pump. a) Place a new gasket on the surface of the cylinder block that meets the oil pump housing. b) Align the keyway of the pump lead rotor with the large key of the crankshaft and place the pump on...

Oil pan and oil pump structure (3S-FE, 4S-FE)
1 - intermediate pulley, 2 - toothed pulley of the crankshaft, 3 - oil seal, 4 - oil pump, 5 - gasket, 6 - oil dipstick, 7 - oil depressant, 8 - oil receiver, 9 - manifold stand, 10 - stiffener, 11 - oil depressant, 12...

Oil Pump and Oil Pan (3S-FE, 4S-FE) — Removal
1. Drain the oil from the engine. 2. Remove the timing belt. 3. Remove the intermediate pulley. 4. Remove the crankshaft toothed pulley. 5. Remove the oil dipstick. 6. (2WD model) Remove the center beam. 7. Remove the...

Oil pump and oil pan (3S-FE, 4S-FE) — installation
1. Install the oil pump by tightening 12 bolts. Tightening torque - 9 Nm 2. Install the oil separator and oil receiver. 3. Install the oil pan. a) Remove the old sealant from the surfaces of the oil pan and block joint,...

Oil pump and oil pan (2C) — removal
1. Drain the oil from the engine. 2. Remove the timing belt. 3. Remove the oil dipstick. 4. Remove the crankshaft toothed pulley. 5. (2WD model) Remove the exhaust downpipe mounting brackets. 6. (4WD model) Remove the...

The structure of the oil pan and oil pump (2C)
1 - generator drive belt adjusting bar, 2 - oil dipstick, 3 - oil pump, 4 - gasket, 5 - oil seal, 6 - toothed pulley of the crankshaft, 7 - bracket for the exhaust system inlet pipe (2WD), 8 - bracket for the exhaust...

Oil pump and oil pan (2C) — installation
1. Install a new gasket into the groove of the oil pump housing. Apply sealant (layer thickness 2-3 mm) to the areas of the oil pump body marked with a dotted line in the figure. Note: The sealant layer around the bolt...

Checking the oil pump
1. Check the pressure reducing valve. After lubricating the valve surface with fresh engine oil, install it into the seat hole and make sure that the valve drops under its own weight. If this does not happen, replace...

Oil pump — disassembly and assembly
For replacement of the front crankshaft oil seal, see chapter " Engine - General Repair Procedures ", chapter " Cylinder block ". Disassembly 1. Remove the pressure reducing valve by removing the snap ring, spring stop...

Oil cooler device (2C, 2WD model)
1 - connector, 2 - emergency oil pressure sensor, 3 - bypass bolt No.2, 4 - gasket, 5 - oil cooler hose, 6 - oil cooler, 7 - O-ring seal, 8 - oil cooler hose, 9 - bypass bolt No.1.

Removal and installation the oil cooler (2WD models)
1. Unscrew the emergency oil pressure sensor. Tightening torque - 15 Nm 2. Remove the oil cooler by loosening the bypass bolts and disconnecting the crossbars. Tightening torque - 53 Nm Note: The oil cooler is installed...

Oil cooler device (2C, 4WD model)
1 - air filter cover with air duct, 2 - oil cooler, 3 - gasket, 4 - oil cooler hose No.1, 5 - oil filter, 6 - oil cooler hose No.2, 7 - check valve.

Removal the oil cooler (4WD model)
1. Drain the coolant. 2. Remove the air filter cover with air duct. 3. Remove the oil filter. 4. Remove the oil cooler. a) Disconnect the two hoses from the oil cooler. b) Unscrew the nut and remove the oil cooler. 5....

Checking the Oil Cooler (4WD Model)
1. Check the check valve. Press the check valve and check for free movement. Replace the valve if necessary. 2. Check the oil cooler for damage and clogging. Replace the oil cooler if necessary.

Installing an Oil Cooler (4WD Model)
1. Install the bypass valve. Tightening torque - 165 Nm 2. Install the oil cooler. a) Clean the contact surfaces of the oil cooler and the mating part. b) Install a new O-ring and gasket onto the oil cooler. c) Install...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Lubrication system Toyota Corolla E80 (1983-1990)
➥ Lubrication system Toyota Corona T190 (1992-1997)
➥ Lubrication system Toyota Duet (1998-2004)

Link in different formats to this article

TEXTHTMLBB Code