Car engine cooling system Toyota Carina 6 (T190)

Coolant pump device (A-series engines)
1 - right engine support, 2 - left (front) engine support, 3 - wire harness protection, 4 - high-voltage wires, 5 - wiring harness, 6 - power steering pump, 7 - oil dipstick, 8 - oil dipstick guide, 9 - O-ring seal, 10...

Removal the coolant pump (A series)
See also section " Timing belt " chapters " Petrol engines 4A-FE, 5A-FE, 7A-FE ". Disconnect the negative terminal from the battery. 2. Drain the coolant. 3. Perform the following operations: (4A-FE, 5A-FE) a) Remove...

Installing the Coolant Pump (A Series)
1. Install the coolant pump. a) Connect the inlet pipe with a hose to the pump. b) Install a new O-ring into the block. c) Install the pump together with the inlet pipe by tightening the 3 mounting bolts. Tightening...

Coolant pump device (3S-FE, 4S-FE)
1 - coolant pump assembly, 2 - gasket, 3 - O-ring seal, 4 - pump cover, 5 - coolant bypass tube No.1, 6 - generator assembly and adjusting bar, 7 - cooling system inlet pipe, 8 - thermostat, 9 - intermediate pulley.

Coolant pump device (2C)
1 - right support, 2 - washer reservoir, 3 - power steering pump, 4- power steering pump drive belt, 5 - power steering pump pulley, 6 - timing belt cover No.2; 7 - gasket, 8 - timing belt, 9 - timing belt guide, 10 -...

Coolant pump (3S-FE, 4S-FE) — removal and installation
Removal 1. Drain the coolant. 2. Remove the timing belt (see Chapter " Petrol engines 3S-FE, 4S-FE ", chapter " Timing belt "). 3. Remove the generator assembly and the generator drive belt tensioner adjusting bar. 4....

Coolant pump (2C) — removal and installation
Note: The pump is installed in the reverse order of its removal. 1. Drain the coolant. 2. Remove the timing belt (see chapter "Diesel engine 2C ", chapter " Timing belt "). 3. Remove the fuel injection pump pulley (see...

Checking the coolant pump
1. Check the coolant pump. Check that the coolant pump bearing operates smoothly and quietly. Replace the pump if necessary. 2. Check that the viscous coupling is not damaged and that there are no leaks. Replace the...

Thermostat — removal, installation, testing
Removal Note: - Do not remove the thermostat unless necessary. - When removing the thermostat, the engine tends to overcool, so do not remove the thermostat even if the engine overheats. The optimum operating...

Cleaning the radiator
Flush the radiator with a pressure hose to remove any dirt from the core. Note: if the water pressure at the outlet of the hose is higher than 30-35 bar, it is necessary to keep the spray nozzle at a distance of 40-50...

Radiator check
1. Remove the radiator cap. Caution: When the engine is hot, this operation must be carried out with caution to avoid burns from a jet of hot water or steam. 2. Check the radiator cap using a radiator tester. Note: - If...

Electric fan of the cooling system
Checking on the engine 1. Check the operation of the electric fan of the cooling system when the engine operating temperature is no more than 83°C. a) Turn on the ignition. 6) Make sure that the electric cooling fan is...

Checking the electric fan
Note: Depending on the design, two electric fans may be installed. 1. Disconnect the electric fan connectors. 2. Check the electric fan. a) Connect the battery and ammeter to the electric fan connector. b) Check that...

Main Engine Relay
1. Measure the resistance between the relay terminals using an ohmmeter. 2. Apply voltage from the battery to terminals "1" and "3" of the relay and check for conductivity between the relay terminals.

Electric Fan Relay
1. Measure the resistance between the relay terminals using an ohmmeter. 2. Apply voltage from the battery to terminals "1" and "2" of the relay and make sure there is no conductivity between terminals "3" and "4".

Coolant Temperature Switch Sensor
1. Check the coolant temperature switch sensor. a) Using an ohmmeter, check that there is no continuity between the terminals of the sensor-switch when the coolant temperature is above 93°C. b) Using an ohmmeter, check...

Checking the fan motor (2C)
Note: Models with air conditioning are equipped with two electric fans (one is an electric fan for the cooling system radiator, and the second is used to cool the air conditioning condenser). 1. Disconnect the fan...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Cooling and heating Toyota Cruiser 100 (1998-2007)
➥ Cooling and heating Toyota Camry XV10 (1991-1996)
➥ Cooling and heating Toyota RAV 4 XA20 (2000-2005)
➥ Cooling and heating Toyota Highlander 1 (2000-2007, petrol)
➥ Cooling and lubrication system Toyota Dyna Y50/Y60 (1984-1995)
➥ Cooling and heating Toyota 4Runner N120 (1989-1995)

Link in different formats to this article

TEXTHTMLBB Code