Engine electrical equipment Toyota Land Cruiser 100

Engine electrical equipment — general information
The engine electrical equipment includes components of the ignition, charging and starting systems. Due to the fact that these systems are directly related to the operation of the engine, they are considered separately...

Engine Electrical Specifications
Ignition system Characteristic Meaning Type Engines 2UZ–FE Built-in ignition coil caps Engines 1HD–FTE Compression ignition, direct ignition system Toyota Setting the ignition timing angle of the 2UZ–FE engine (with...

Removal and installation the battery
1. Starting with the negative, disconnect both cables from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before...

Checking the condition and replacing battery wires
Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting the battery! Attention! The cars of the model in question...

Ignition System — General Information and Precautions
The models discussed in this manual use a direct ignition system without a distributor and high-voltage wires. Direct ignition systems include camshaft and crankshaft position sensors (CMP and CKP), a set of individual...

Checking the functioning of the ignition system
Caution! Due to the very high voltage generated in the ignition system, its components must be serviced with extreme caution. This applies not only to the main components of the electronic ignition system, but also to...

Replacing the ignition coil
Coil assembly installation details 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio...

Checking and adjusting the ignition timing/fuel injection angle
Note: In case of discrepancies with the data given on the VECI label, the latter should prevail. General information Ignition timing is measured in degrees of engine crankshaft rotation and is important for firing the...

Replacing the ignition module
On models equipped with a direct ignition system (DIS), the module is combined with the coil into a single assembly and cannot be replaced individually.

Charging system — general information and precautions
Functional diagram of a typical charging system 1 - Ignition switch; 2 - Main fuse link; 3 - Charge indicator lamp; 4 - Voltage regulator; 5 - Stator winding; 6 - Rotor winding; 7 - Battery; 8 - Generator The components...

Checking the status of the charging system
Functional diagram of a typical charging system 1 - Ignition switch; 2 - Main fuse link; 3 - Charge indicator lamp; 4 - Voltage regulator; 5 - Stator winding; 6 - Rotor winding; 7 - Battery; 8 - Generator 1. Remember...

Removal and installation the generator
Generator Installation Details 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio...

Checking the condition and replacing generator components
Disassembly Typical construction of an automotive alternator 1 - Pulley; 2 - Drive side cover; 3 - Front bearing; 4 - Holder; 5 - Rotor; 6 - Rear bearing; 7 - Bearing cover; 8 - Rubber insulating insert; 9 - Spring; 10...

Starting System — General Information and Precautions
The system ensures the engine is turned over in order to start it. The main components of the system are the starter with the traction relay installed on it (electromagnetic starter), battery, ignition switch and...

Checking the serviceability of the starter and starting circuit
Note: Before checking the starter condition, make sure the battery is fully charged. 1. If the starter does not turn when the ignition key is turned to the START position, first make sure that the selector lever is in...

Removal and installation the starter
1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting the...

Removal and installation the traction relay
1. Remove the starter (see section Removal and installation the starter ). 2. Use a scriber or paint to mark the position of the starter motor housing relative to the reduction gear section (refer to the accompanying...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Engine electrical equipment Toyota Carina T190 (1992-1996)
➥ Engine electrical equipment Toyota Highlander 1 (2000-2007, petrol)
➥ Engine electrical equipment Toyota Camry XV20 (1996-2001)
➥ Engine electrical equipment Toyota RAV 4 XA20 (2000-2005)
➥ Engine electrical equipment Toyota Corona T190 (1992-1997)

Link in different formats to this article

TEXTHTMLBB Code