Engine electrical equipment — general information The engine electrical system includes an ignition system, a battery charging system and an engine start system. When caring for electrical equipment, take extreme care when inspecting parts and appliances of electrical...
Battery — removal and installation Starting the engine in an emergency When starting the engine from the battery of another vehicle in an emergency, observe the polarity of the battery connection. Removal and installation 1. Disconnect both cables from...
Power Cables — Inspection and Replacement 1. Periodically check the cables along the entire length, damage, cracking or burning of the cable insulation, as well as corrosion are not allowed. A poor battery connection can cause engine start failures and engine...
Ignition system — design description Scheme of car ignition 1980-87 1, 10. Fusible link; 2, 9. Ignition lock; 3. Connector on the side of the lock; 4. Distributor; 5, 13. Candle; 6, 11. To the tachometer; 7. Ignition coil with electronic switch; 8. Coil;...
Checking the ignition system Attention! The ignition system generates a very high voltage, therefore, when performing work, electrical safety rules must be observed. 1. If the engine does not start, and the starter turns the crankshaft, then...
Ignition coil — check and replacement Examination 1. Disconnect the battery from the ground. 2. Remove the plastic spool cap (if provided). 3. Remove the two coil connector screws and connect the ohmmeter leads. 4. Measure the resistance between the...
Ignition distributor — removal and installation Ignition distributor 1988-92 1. Seal; 2. Housing; 3. Gear; 4. Ring; 5. Pin Ignition distributor 1980-87 1. Housing and spiral gear; 2. Sensor rotor; 3. Counterweights of the centrifugal regulator; 4. Breaker plate; 5....
Electronic ignition unit — replacement Electronic ignition unit mounted: on cars 1980-87. - on the coil body; on cars 1988-92. - on the mudguard in the engine compartment; on cars since 1993 - on the bulkhead of the engine compartment, next to the brake...
Induction sensor — check and replacement Checking the gap between the rotor and the protrusion of the inductive sensor (1980-87) 1. Induction sensor 2. Gap between the rotor and the protrusion of the inductive sensor Checking the gap in the inductive sensor on...
Battery Charging System — Design Description Battery Charging Circuit Diagram (1988-92) 1. Fusible link; 2. Relay of a control lamp; 3. Control lamp; 4. ENGINE fuse; 5. GAUGE fuse; 6. Charge circuit fuse; 7. Ignition control relay Battery Charging Circuit Diagram...
Checking the battery charging system Charge system units on cars after 1993 1. Main fuse link FL 2.0L; 2. Fuse IGN 7.5 A; 3. Charge fuse 7.5 A; 4. Fuse AM1 (50 A); 5. Fuse AM1 FL 1.25 V; 6. Generator; 7. Fuse AM2 0.3P Circuit for checking battery charge...
Generator — removal and installation Generator mounting details 1. Power steering reservoir; 2. Adjustment bracket; 3. Wire; 4. connector; 5. Generator; 6. Belt; 7. Locking bolt; 8. Axis Removal and installation 1. Lower engine and connect to clutch...
Generator parts — disassembly, inspection and assembly Generator parts (1980-87) 1. Coupling bolt; 2. Pulley and impeller; 3. Separating sleeve; 4. Front cover and bearing; 5. Ring; 6. Rotor and bearing; 7. Capacitor; 8, 12. Insulator; 9. Back cover; 10. Regulator; 11....
Engine starting system — design description Engine start system (1980-87) 1. Ammeter; 2. Ignition lock; 3. To the ignition coil; 4. Conclusion C; 5. Conclusion 50; 6. Conclusion 30; 7. Fusible link Engine starting units on cars after 1993 1. Blocking switch; 2....
Starter pull relay (a / m 1980-87 release) Car starter parts 1980-87 1, 5, 8. Bolt; 2. Traction relay; 3. Bearing housing; 4. Lock washer, ring and rubber washer; 6. Back cover; 7. Yoke and brush holder; 9. Front cover; 10. Lever; 11. Anchor; 12. Spring ring and...