Drive shafts and axles of the car Toyota Land Cruiser 60/80

Cardan shaft, gearbox and axles — general information
The cars are equipped with 2 cardan shafts (front and back), which transmit torque from the transfer case to the gearboxes of the rear and front axles. The shafts are equipped with 2 cardan fork joints. The cardan...

Checking cardan shafts and joints
1. Raise the vehicle and place it on stands. 2. Inspect the cardan shafts. If there are dents, cracks or deformations, replace the shaft. 3. If traces of leakage are detected near the transfer case or gearbox, replace...

Removal and installation the propeller shaft
1. Raise the car. 2. To maintain dynamic balance during assembly, mark the relative positions of the cardan shaft forks and the flanges of the drive gear of the gearbox. 3. Also mark the relative position of the sliding...

Cardan joints — replacement
Cardan joint parts 1. Retaining ring; 2. Bearing; 3. Crosspiece; 4. Fork with flange Replacement 1. Remove the driveshaft. 2. Clamp the shaft in a vice, mark the position of the hinge forks and remove the bearing cup...

Locking hub — removal and installation
Manual locking hub 1. Conical washer and nut; 2. Hub cap and gasket; 3. Retaining ring; 4. Hub housing and gasket Manual locking hub coupling parts 1, 7. Retaining ring; 2. Gasket; 3. Body; 4. Hub cap flange; 5. Handle...

Front axle shaft and seal — removal and installation
Orientation of the CV joint cage and guide during assembly 1. Large window; 2. Protruding part; 3. Flat side; 4. Extended section; 5. Narrow part Removal 1. Remove the hub. 2. Remove the front wheel bearings (see...

Rear (front) axle — removal and installation
1. Raise the vehicle and place it on stands. 2. Remove the wheels. 3. Remove the brake components. 4. On the front axle, disconnect the steering rods. 5. Disconnect the cardan shaft from the axle gearbox. 6. Disconnect...

Gearbox seal — replacement
Wear of the seal is detected by traces of oil on the fork or flange of the universal joint. The seal is changed without removing the bridge. Replacement 1. Raise the vehicle to clear the wheels. 2. Drain the oil from...

Half shaft, bearing and seal (semi-unloading half shafts)
Rear axle parts with semi-floating axle shaft 1. Handbrake cable clamp; 2. Cable; 3. Gearbox cover; 4. Gasket; 5. Bearing; 6. Seal; 7. Drum; 8. Gasket; 9. Oil deflector; 10. Half shaft; 11. Locking plate; 12. Satellite...

Half shaft and seal (fully unloaded half shafts)
Removal and installation 1. Unscrew the nuts (indicated by arrows) axle shaft flange and remove the washers. 2. Loosen the conical washers by tapping the axle stud through a brass mandrel and remove them from the hub....

Rear wheel hub (fully unloaded axle shafts)
Removal and installation 1. Raise the vehicle and remove the rear wheels. 2. Remove the axle shaft. 3. Loosen the locking screws. 4. Loosen the lock nut. 5. Remove the retaining ring. 6. Move the hub by pushing it...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Drive shafts and cardan Toyota Duet (1998-2004)
➥ Drive shafts and cardan Toyota Corona T190 (1992-1997)
➥ Drive shafts Toyota Carina T170 (1988-1992)
➥ Drive shafts and cardan Toyota Highlander 1 (2000-2007, petrol)

Link in different formats to this article

TEXTHTMLBB Code