Vehicle cooling and heating Toyota Camry 1 (XV10)

Technical characteristics of the cooling system
Radiator cap pressure 5S-FE engine 0.72 – 1.00 bar 3VZ-FE V6 engine: - on the radiator 0.90 – 1.20 bar - at the exit 0.80 – 1.10 bar engine 1MZ-FEV6 0.80 – 1.10 bar Tightening moments Thermostat Housing Bolts: – 5S-FE...

General information about the cooling and heating system
Elements of the engine cooling system 1 – Coolant inlet pipe; 2 – thermostat; 3 – water pump; 4 – IAC valve; 5 – coolant outlet from the engine; 6 – oil radiator Location of the coolant supply pipe to the engine on the...

Antifreeze — General Information
Antifreeze is a mixture of distilled water and ethylene glycol concentrate. Antifreeze provides protection for the cooling system from corrosion and increases the boiling point of the coolant. The amount of ethylene...

Cooling system hoses
Check the condition of the cooling system hoses and if a defect is found, replace the hose as follows. 1. Drain the coolant from the cooling system. 2. Remove the hose clamps and slide the clamps down the hose. Pull the...

Checking and replacing the thermostat
Examination If there are any defects in the cooling system, check the coolant level and the functionality of the temperature gauge. 1. If the engine warms up very slowly after starting, the thermostat may be permanently...

Checking and replacing the radiator fan and relay
Examination Location of the radiator fan switch temperature sensor in the lower radiator tank on models with four-cylinder engines The fan is controlled by a temperature sensor installed in the radiator. On the 1MZ-FE...

Radiator Fan (V6 Models 1992 — 1994)
Elements of the radiator fan hydraulic drive system 1 – coolant temperature sensor; 2 - hydraulic pump; 3 - Radiator Fan Control Unit (ECU); 4 - throttle position sensor; 5 - ignition unit; 6 - oil filter; 7 - pressure...

Radiator — removal and installation
Removal Attention! Remove the radiator on a cold engine. Caution! Avoid contact of coolant with clothing and paintwork. If this happens, rinse the surface with plenty of water. 1. Remove the ground cable from the...

Expansion tank — removal and installation
1. On most models, the expansion tank is simply removed by pulling it out of the bracket. 2. Drain the coolant from the expansion tank into a container and inspect the condition of the expansion tank. 3. The tank is...

Water pump — removal and installation
Models with four-cylinder engines Location of the generator adjusting rod mounting bolt 1. Remove the ground cable from the battery. Warning: If your radio has an anti-theft code, make sure you have the connection codes...

Coolant Temperature Sensor — Checking and Replacing
Examination Coolant Temperature Sensor Location on a Four Cylinder Engine Location of the coolant temperature sensor on the engine 1 MZ-FE 1. If the temperature gauge does not work, check the fuses in the electrical...

Heater Fan — Removal and Installation
1. Remove the ground cable from the battery. 2. The fan is located on the right side under the instrument panel. 3. Remove the glove box, glove box cover and lower trim panel under the glove box. 4. Disconnect the...

Heater Fan Resistor — Check
Heater Fan Resistor Location The resistor is located to the right of the accelerator pedal and is attached to the rear of the air conditioning control unit. Heater Fan Resistor Test Diagram 1. Disconnect the electrical...

Heater radiator — removal and installation
1. Remove the ground cable from the battery. Warning: If your radio has an anti-theft code, make sure you have the connection codes before disconnecting the battery. Caution! On models from 1993 onwards, the airbag...

Heater control panel
Heater control panel elements A – temperature control knob; B – heater control cable; C – fan switch; D – electrical connector. 1. Remove the ground cable from the battery. Warning: If your radio has an anti-theft code,...

Air Conditioning System — Information and Precautions
Location of the main components of the air conditioning system 1 – capacitor; 2 – compressor; 3 – receiver; 4 – evaporator; 5 – valve Location of the sight glass to determine the refrigerant level in the air...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Cooling and lubrication system Toyota Cruiser 70 (1985-1996, diesel)
➥ Cooling and heating Toyota RAV 4 XA20 (2000-2005)
➥ Cooling system Toyota Corolla E80 (1983-1990)
➥ Cooling and heating Toyota Highlander 1 (2000-2007, petrol)
➥ Cooling and lubrication system Toyota Dyna Y50/Y60 (1984-1995)
➥ Cooling and heating Toyota 4Runner N120 (1989-1995)

Link in different formats to this article

TEXTHTMLBB Code