Car rear suspension Toyota Vista 4 (V40)

Rear Wheel Alignment (2WD-2WS)
1. Check the toe-in value. Toe-in during checking: B - A = 4 ±2 mm If the toe-in does not meet the specified conditions, then adjust the toe-in. a) Measure the distance shown in the figure for the left and right lower...

Adjusting the rear wheel alignment angles (2WD — 4WS)
Attention: check and adjust the rear wheel alignment angles after checking and adjusting the front wheel alignment angles. raise the front wheels. Checking the wheel turning angles 1. Place the vehicle on the stand and...

Adjusting the rear wheel alignment angles (4WD — 2WS)
1. Check the toe-in value. Toe-in when checking: B - A = 4 + 2 mm If the toe-in does not meet the specified conditions, then make adjustments. a) Measure the distance shown in the figure for the left and right lower...

Rear Wheel Hub (2WD Models)
Removal Note: Installation is performed in the reverse order of removal. After installation, check the operation of the speed sensors (ABS). 1. Jack up the car, remove the rear wheel. Tightening torque - 105 Nm 2....

Hub and knuckle (4WD models)
Removal Note: Installation is performed in the reverse order of removal. After installation, check the operation of the speed sensors (ABS) and the rear wheel alignment angles. 1. Remove the rear wheel. Tightening...

Fist (2WS models)
Removal Note: Installation is performed in the reverse order of removal. After installation, check the operation of the speed sensors (ABS) and the rear wheel alignment angles. 1. Remove the hub ( see the relevant...

Fist (4WS models)
Removal Note: Installation is performed in the reverse order of removal. After installation, check the operation of the speed sensors (ABS) and the rear wheel alignment angles. Rear wheel knuckle (4WS models). 1 - rear...

Rear suspension strut
Removal Note: Installation is performed in the reverse order of removal. After installation, check the rear wheel alignment angles and the operation of the speed sensors (ABS). 1. Jack up the car and remove the rear...

Steering knuckle arm (4WS models)
Removal Note: Installation is carried out in the reverse order of removal. 1. Place the crowbar as shown in the figure, check that there is no gap in the ball joint of the steering knuckle arm. 2. Disconnect the tie rod...

Lower and trailing arms (2WS models)
Removal Note: Installation is performed in the reverse order of removal. After installation, check the rear wheel alignment angles and the operation of the speed sensors (ABS). Note: After installation, press the body...

Lower and trailing arms (4WS models)
Removal Note: Installation is carried out in the reverse order of removal. Note: After installation, press the body down and lift it up to stabilize the suspension. 1. Jack up the car and remove the rear wheel. 2....

Lower and trailing arms (4WD models)
Removal 1. Jack up the car and remove the rear wheel. Tightening torque - 105 Nm 2. Loosen the two bolts and disconnect the parking brake cable bracket. Tightening torque - 5.5 Nm 3. Remove the trailing arm. a) Unscrew...

Transverse stability stabilizer
Removal Note: Installation is carried out in the reverse order of removal. 1. Jack up the car and remove the rear wheels. Tightening torque - 105 Nm 2. Remove the stabilizer struts. Note: If the ball joint axle rotates...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ Rear suspension Toyota Carina T170 (1988-1992)
➥ Rear suspension Toyota Corona T190 (1992-1997)
➥ Rear suspension Toyota Corolla E80 (1983-1990)
➥ Rear suspension Toyota RAV 4 XA20 (2000-2005)

Link in different formats to this article

TEXTHTMLBB Code