4-cylinder car engine Toyota Camry 1 (XV10)

Technical characteristics of 4-cylinder engines
Engine type 5S-FE Cylinder firing order 1–3–4–2 Cylinder head Non-flatness: – cylinder block mating surface 0.05 mm – collector mating surface 0.08 mm Toothed belt Length of the idler pulley spring 45 mm...

Engine repair operations on a car
Many engine repairs can be performed directly on the vehicle. Before starting repairs, it is recommended to thoroughly clean the engine and engine compartment. Depending on the type of work, the hood may be removed to...

Top dead center of the first cylinder
Attention! The sequence of operations is presented on the assumption that the ignition distributor is installed correctly. If it is necessary to determine the top dead center for installing the distributor, then set the...

Cylinder Head Cover — Design Description
Cylinder head parts for 5S-FE engine 1 – engine lifting eye; 2 – ground bus; 3 – generator bracket; 4 – cylinder head gasket; 5 – rear timing belt cover; 6 – spring washer; 7 – thrust ring; 8 – washer; 9 – sealing ring;...

Cylinder Head Cover — Removal and Installation
Removal Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the battery. Caution! On models from 1993 onwards, the airbag system is disabled if the battery is...

Intake manifold — removal and installation
Removal Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the battery. Caution! On models from 1993 onwards, the airbag system is disabled if the battery is...

Exhaust manifold — removal and installation
Caution! Before performing work on the exhaust manifold, it is necessary to pre-cool the engine. Removal Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the...

Timing Belt and Pulleys — Removal, Checking and Installation
Removal Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the battery. Caution! On models from 1993 onwards, the airbag system is disabled if the battery is...

Replacing the front crankshaft seal ring
1. Remove the timing belt and crankshaft pulley. 2. Using a screwdriver with a blade covered in adhesive tape, remove the crankshaft sealing ring from its seat. Be careful not to damage the sealing ring seat or the...

Replacing the camshaft sealing ring
1. Remove the timing belt, upper idler pulley and camshaft pulley. 2. Remove the rear timing belt cover. 3. Mark the camshaft seal installation depth and use a small screwdriver to remove the seal. 4. Clean the seal...

Camshaft and tappets — removal, inspection and installation
Removal 1. Remove the cylinder head cover. 2. Remove the ignition distributor. 3. Remove the timing belt, camshaft pulley and upper timing belt cover. 4. Using a dial indicator, measure the camshaft end play. 5. If the...

Cylinder head — removal and installation
Removal Attention! The cylinder head must be removed on a cold engine. Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the battery. Caution! On models from...

Oil pan — removal and installation
Removal Warning! If your radio has an anti-theft code, check that you have the connection codes before disconnecting the battery. Caution! On models from 1993 onwards, the airbag system is disabled if the battery is...

Oil pump — removal and installation
Oil pump parts 1 – pulley; 2 – oil pump cover; 3 – inner rotor; 4 – circular section sealing gasket; 5 – outer rotor; 6 – oil pump housing; 7 – gasket; 8 – safety valve piston; 9 – spring; 10 – retainer; 11 – thrust...

Flywheel/Drive Plate — Removal and Installation
Removal 1. Raise the vehicle and remove the transmission. 2. Mark the position of the clutch master assembly in relation to the flywheel using a marker or paint. 3. Loosen the clutch master assembly mounting bolts...

Replacing the rear crankshaft seal ring
1. Remove the gearbox and flywheel. 2. The easiest way to remove the old sealing ring is to use a screwdriver to pry the sealing ring out of its seat. 3. The O-ring can also be removed from its seat by drilling two...

Powertrain suspension — inspection and replacement
Examination Four-cylinder engine suspension components 1 – front right engine mount; 2 – exhaust manifold suspension; 3 – Engine mount No.2; 4 – moving thrust; 5 – right rear suspension of the power unit Replacement...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Similar sections for other Toyota models

➥ 6-cylinder engine Toyota Highlander 1 (2000-2007, petrol)
➥ Petrol engines 1.3 l Toyota Duet (1998-2004)
➥ Engine repair Toyota Corolla E80 (1983-1990)
➥ Petrol engines 2F and 3F-E Toyota Cruiser 60/80 (1980-1997, petrol)
➥ Engines 4A-FE and 7A-FE Toyota Corona T190 (1992-1997)
➥ 4-cylinder engines Toyota 4Runner N120 (1989-1995)

Link in different formats to this article

TEXTHTMLBB Code